二次型时频分析技术的开发与应用

基于二次型的时频分析是高分辨率时频分析技术的有效方法之一，该项技术能够有效反映时变信号的频谱特性，具有分辨率高、能量集中和跟踪瞬时频率的特点。从时变信号的特点出发，阐述了二次型时频分析技术的基本方法原理，采用正演模型分析验证了该方法的有效性，并在实际地震资料中应用于识别物源方向、划分沉积相带、预测储层结构以及相对厚度等诸多方面，均取得了较好的效果。     

EFFECT OF THE RATIO Th/U ON TL DATING ACCURACY

ＥＦＦＥＣＴＯＦＴＨＥＲＡＴＩＯＴｈ／ＵＯＮＴＬＤＡＴＩＮＧＡＣＣＵＲＡＣＹ￥Ｐ．Ｌ．Ｌｅｕｎｇ（梁宝鎏）；ＭｉｃｈａｅｌＪ．Ｓｔｏｋｅｓ（ＤｅｐａｒｔｍｅｎｔｏｆＰｈｙｓｉｃｓａｎｄＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅ，ＣｉｔｙＰｏｌｙｔｅｃｈｎｉｃｏ...     

Application of a Compaction Simulator to the Design of a High-Dose Tablet Formulation. Part I

The compaction properties of an investigational drug are studied by the use of a compaction simulator. The effects of punch velocity over the range of 30-640 mm^-1 on the compaction properties of the pure drug and a variety of formulas incorporating a high dose of the active compound have been investigated. The data were analyzed by applying the Heckel equation. The pure drug was found to have a high yield pressure at a relatively low punch velocity of 31 mm^-1. As the punch velocity was increased there was a decrease in crushing strength, primarily as a result of increasing yield pressure. These findings indicate that the pure drug predominantly consolidated by fragmentation and elastic deformation, with a slow plastically deforming component. The information obtained on the consolidation mechanism of the pure drug and, subsequently, on model formulas were instrumental in the design and selection of a robust formula and granulation process. The advantages of conducting dosage form design and characterization studies during the early phase of tablet formulation using means such as a compaction simulator are emphasized in this investigation.     

Evaluation of influence of external magnetic disturbance on superconducting magnet taking conservation of linkage flux into account

External magnetic disturbance influences the quality of the image obtained with a magnetic resonance imaging (MRI) system because it causes magnetic resonance frequency drift. When a superconducting magnet in persistent current mode operation is exposed to external magnetic disturbance coil current varies to keep linkage flux constant. Conventional analysis is usually formulated with constant current and does not provide correct evaluation of drift of magnetic field in the magnet. This paper proposes a method of numerical analysis of magnetic field considering conservation of linkage flux in a superconducting magnet under a persistent current mode operation. This method is applied to evaluate drift of the magnetic field in a superconducting magnet for magnetic resonance imaging due to external magnetic disturbance. Analysis results show good agreement with the experimental results.     

Control of polymerization processes of 10,12-pentacosadiynoic acid LB films

Studies have been carried out on KrF excimer laser light (EX), X-ray or electron beam (EB) induced polymerization of 10,12-pentacosadiynoic acid (PDA) Langmuir-Blodgett (LB) films in relation to molecular density or molecular arrangement of the films using X-ray diffraction analysis, infrared (IR) spectroscopy and Raman spectroscopy. The molecular arrangement or density of the PDA LB films was controlled by subphase conditions when the films were built up, such as pH, temperature of a subphase or salt concentration in the subphase. Polymerization sensitivity of the PDA LB film was affected by the arrangement or molecular density. On low density (A type) films the polymerization occurred by irradiation with EX, X-ray or EB, but on high density (B type) films the polymerization occurred only when the irradiation was carried out by high energy beams such as X-ray or EB. Decomposition of polymerized films was observed further by excessive irradiation of EX or X-ray, but not on the B type films. It was revealed by X-ray diffraction analysis that in the A type film, the PDA molecules bent to a larger extent than those in the B type film and the polymerization proceeded topochemically, that is, the thickness decreased little after EB irradiation in a helium atmosphere. On the other hand, in the B type film, the thickness decreased by about 10% as a result of EB irradiation. By IR reflection-absorption (RA) and Raman measurements, it was confirmed that conjugated diacetylenic bonds disappeared and conjugated double and new conjugated triple bonds appeared after high energy beam irradiations. These results support the supposition that 1,4-polymerization, i.e. polydiacetylene type polymerization, occurs easily in the A type film and 1,2- or 3,4-polymerization, i.e. polyacetylene type polymerization, occurs in the B type film, and that the polymerized A type film was decomposed at the polydiacetylenic bond when the irradiation continued further. It was also shown that the polyacetylene type polymer was obtained only when the B type film was irradiated with the high energy beam.     

Strawberry juice colour: The effect of some processing variables on the stability of anthocyanins

The colour stability of juice and purées made from a mixture of two strawberry varieties, stored at + 20°C or at –20°C under aerobic and anaerobic conditions, was studied. High-performance liquid chromatography and spectrophotometric analysis were used to monitor the changes in colour during storage. Pelargonidin 3-glucoside comprised 80% of the total anthocyanin content. Four other pelargonidin-based peaks were found, being 10.4%, 3.5%, 0.7% and 0.3% of the total and two cyanidin peaks were present, being 3.3% and 0.4% of the total. Clarification before storage caused considerable losses in the initial anthocyanin concentrations. Storage conditions (air versus nitrogen) did not influence the rate of loss of anthocyanins during storage or the formation of polymeric pigments. There were no losses in anthocyanins and no increase in the amount of colour measured at 510 nm due to polymers in samples stored at–20°C. Polymerisation occurred in the samples stored at + 20°C, especially in the clarified samples.     

NCFW专家系统的汉语接口

NCFW系统是适合于花岗岩与变质岩地区的勘探地下水专家系统，系统的人机交互既可用菜单（亦称项目单）方式，亦可用汉语对话方式。这两种方式既可混合使用亦能灵活切换。本文着重描述了汉语接口的设计思想、实现中采用关键技术以及系统运行实例。     

High‐Tech‐Cellulose‐Funktionspolymere nach dem ALCERU®‐Verfahren

Functional High‐Tech‐Cellulose materials by the ALCERU® process Cellulose is one of the eldest materials of mankind. While the use of cellulose in former times was focused on application as a more construction or as a more textile material at present time the application profile turns to a more functional material using the ALCERU® process. Shaping of pure cellulose dissolution in NMMNO permits the manufacturing of materials for upholstery, filtration or biodegradable film strips having an uniform cross section. Fibreds, which can be applied in several packaging materials, are available using different techniques for regeneration cellulose. A great field of innovative functional cellulose materials is opened up by addition of several functional additives to cellulose dissolution. In this way piezo‐electrical conductive cellulose fibres (PZT) or high‐temperature filtration membranes are to be generated if one adds special types of ceramic powders. Above all PZT green fibres are applied in more recent uses as sensors or actuators. Electrically conductive cellulose fibres or filaments, which can be also used in the textile chain, can be prepared adding conductive carbon black to a cellulose dope on the same way, too. Cellulose material having adapted conductivity to different application is available by adding an exact defined amount of carbon black to cellulose dissolution. Finally cellulose beads can be manufactured by means of varied shaping technique. The beads are showing variable particle sizes and narrow pore size distribution. These properties open up very interesting application in the field of human blood purification or chromatography.     

Accidents,often the result of an ‘uncontrolled business process’—a study in the (Dutch) chemical industry

Often companies in the (petro‐) chemical industry claim that all possible countermeasures against potential accidents have been taken and therefore accidents are unforeseeable. In this paper we question this statement by analysing the pre‐warning signals (precursors) preceding a number of industrial accidents. 17 accidents that occurred in the (petro‐) chemical industry have been investigated by exploring FACTS, an accident database containing information about industrial accidents worldwide. This paper will demonstrate that the existence of precursor information could have been used to foresee and even prevent these accidents if a proper control action had been initiated. The accidents are analysed further, according to a control model, which was adapted from that of C. Argyris. It demonstrates the ineffectiveness of several elements of business process control loops and that the so‐called ‘double‐loop learning’ cycle is more important than the ‘single‐loop learning’ cycle if one considers safety improvement. Copyright © 2003 John Wiley & Sons, Ltd.