Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

Fast convergent study on potential－harmonic method of directly solving Schrodinger equation in few－body systems

Ｆａｓｔｃｏｎｖｅｒｇｅｎｔｓｔｕｄｙｏｎｐｏｔｅｎｔｉａｌ－ｈａｒｍｏｎｉｃｍｅｔｈｏｄｏｆｄｉｒｅｃｔｌｙｓｏｌｖｉｎｇＳｃｈｒｏｄｉｎｇｅｒｅｑｕａｔｉｏｎｉｎｆｅｗ－ｂｏｄｙｓｙｓｔｅｍｓＷａｎｇＹｉ－Ｘｕａｎ（王沂轩）ａｎｄＤｅｎｓＣｏｎｇ...     

涂层材料的断裂分析(英文)

和基体厚度相比,涂层很薄,因此细观力学模型可把基体作为半无限弹性体。由于涂层和基体材料的膨胀系数及弹性系数不匹配,涂层材料中残余热应力的解析解为 E_c/(1-γ_c)·(α_s-α_c)△T。用有限元法校核,该应力和解析解吻合得好。通过对涂层产生裂纹驱动力和断裂韧性的讨论,提出了抗裂涂层厚度公式。     

汛期采金船的缆绳牵拉

本文介绍了采金船渡汛时的停泊方向及采金船在洪水中可能产生拖曳力的估算方法，为了防止采金船汛期发生溜船事故，建议采用缆绳牵拉固船的措施，以保障采金船的汛期安全。     

水闸闸室化算梯形横截面上不平衡剪力的分配计算

当地弹性地基梁法计算非岩石地基的水闸底板应力时，首先要求解出不平衡剪力，当闸墩截面选择梯形时（主要是边墩），常用方法是作图法，这既有误差又繁琐。所以就此推导出一个公式，可直接求解平衡剪力。     

用双向扭转圆柱组合螺旋弹簧实现扭矩测试

利用单个圆柱螺旋扭转弹簧扭转原理,给出了一种用双向扭转圆柱组合螺旋弹簧实现扭矩测试的方法。根据扭转弹簧模型,给出了预紧力、加载的证明,并对实验结果进行分析;该结构用于扭矩测试系统既实用可靠,又简单易加工;降低了测试系统的成本,具有很高的实用价值。     

采用荷载平衡的概念表达预应力度及在初步设计中的应用

利用荷载平衡法的概念，将预应力度用等效荷载与外荷载的比值表达，设计可利用其比值确定预应力度，便其更简捷，明确，同时，提出了预应力度的真实值问题。     

Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

Formation and investigation of epoxy intumescent compositions modified by active additives

Results are reported of research on intumescent composites based on epoxy resin cross‐linked with polyethylene polyamine and containing ammonium polyphosphate and such modifying additives as calcium borate, manganese dioxide, nickel, and chromium, containing tubulenes as gas‐formers and carbonization stimulators. The changes in composition and physicochemical properties of modified compositions under conditions of heat and fire were investigated by X‐ray photo‐electron spectroscopy, atomic force microscopy, and local force spectroscopy. Ammonium polyphosphate mainly stimulates carbonization processes on the inner surface of a bubble being formed during foam coke formation. The introduction of metal‐containing tubulenes leads to the formation of fire‐retardant and low flammability‐compositions with high coke and carbon structures content. The use of calcium borate in the compositions considerably increases the strength of foam coke being formed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1477–1483, 2002