螺旋焊管内涂层涂敷挥发份的清除

针对大口径螺旋焊管内涂层涂敷作业时，钢管内残留的涂料挥发份如何清除的问题，介绍了一种自行设计制造的内涂层涂敷挥发份吹除装置。     

关于化粪池几个问题的探讨

探讨化粪池在设计布置及使用管理中应注意的几个问题，以充分发挥化粪池在保护环境，减轻污染方面的作用。     

Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

土壤源热泵取热的实验研究

通过广泛分析国内外对土壤源热泵实验研究的现状,建立了可以模拟多个地区、多种运行工况的土壤源热泵沙箱实验台,并进行了绝热边界工况短期内取热的实验研究。     

液化天然气供气站的工艺设计

〗LNG供气站的设计核心是工艺设计，设计中应注意以下几点：正确处理技术先进性与经济合理性的关系，综合权衡设置费与运营费的比例，力求项目全寿命费用最低；大多数城市LNG供气站均利用空气气化LNG，单罐容积为100 m³的真空压力式储罐广泛用于储存量为1200 m³以下的LNG供气站；为正确设置储罐安全阀的开启压力和排放压力，必须根据储罐的最高工作压力按照规范正确确定储罐的设计压力；储罐上2套独立的液位计和高、低限报警自动切断装置可确保储罐安全运行；空温式气化器的气化能力按用气城市高峰小时计算流量的1.3~1.5倍确定，为便于自然化霜应设置2套空温式气化器切换使用；空温式气化器出口串接水浴式加热器可提高冬季或雨天出口天然气温度，保护碳钢管道并降低供销差；LNG储罐区应设置围堰，消防用水量为喷淋与水枪用水量之和。最后建议，必须尽快颁布国家LNG设计规范，以提高我国的LNG设计水平。     

以表面负载季铵盐阳离子型苯/丙乳胶粒为模板制备ZrO_2空心微球

以C9油与甲基丙烯酰氧乙基三甲基氯化胺的共聚物P(C9-DMC)为乳化剂制备苯/丙阳离子乳胶粒,并以其为模板,利用直接包覆法制备了由17 nm左右微晶体堆成的ZrO2空心微球。所制得的样品采用FT-IR、XRD、TEM和SEM等进行了表征。     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

12．5×10^4 m3储油罐底板阴极保护方案比选

对国内外储油罐底板内外侧各种阴极保护方法进行了分析对比。重点介绍了茂名分公司12.5×10~4m~3储油罐底板内外侧阴极保护方案:内侧为涂料加铝合金牺牲阳极阴极保护;外侧为涂料加混合金属氢化物网状阳极阴极保护。