用模糊综合评判法评估钢制储罐的寿命

针对影响钢制储罐寿命的因素具有复杂性、非确定性以及时变性的特点,提出了用动态二级模糊综合评判的方法对其寿命进行评估,建立了评估的数学模型和评估流程。在对某石油库油罐的寿命分析中,考虑到保留所有评判因素的影响,采用了乘、加型模糊算子,并用层次分析法来确定评价指标权重。计算结果表明,该方法能够解决储罐寿命评估中的一些复杂因素的处理问题,具有一定的实际工程意义。     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

Surface structural change of ZnO-coated LiNi0.5Mn1.5O4 spinel as 5 V cathode materials at elevated temperatures

LiNi_0.5Mn_1.5O₄ powder was synthesized via sol-gel method and coated with ZnO in order to test the electrochemical cyclability of the material as a cathode for the secondary Li battery in the 5 V range at 55 °C. The ZnO-coated LiNi_0.5Mn_1.5O₄ powder nearly maintained its initial capacity of 137 mA h g⁻¹ after 50 cycles whereas the uncoated powder was able to retain no more than 10% of the initial capacity after 30 cycles. TEM analysis of the cycled cathodes suggests that the formation of the graphitic surface phase, hindering the Li migration, may be responsible for the rapid capacity loss of the uncoated material while no such phase was observed on the surface of the ZnO coated LiNi_0.5Mn_1.5O₄ powder.     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

埋地管道三层PE外覆盖层及其检测方法研究

文章介绍了埋地管道三层PE外覆盖层系统的构造参数和性能特点,论述了两种用于埋地钢质管道外覆盖层状况检测的方法,一种是多频管中电流法,另一种是DCVG/CIPS组合检测技术。分别介绍了两种方法的工作原理、操作方法和设备,并结合工程实例进行了说明。这些方法和设备可分别或同时用于管道不开挖检测防腐层破损点的位置以及漏点大小。     

纳米涂层的研究现状与展望

简述了纳米表面涂层制备工艺的研究现状，分析了气相沉积、热喷涂、电刷镀、化学镀和电沉积等不同工艺在制备纳米表面层中的应用情况。介绍了纳米涂层在超硬耐磨、耐腐蚀、耐高温热稳定性等方面研究的新进展，并对纳米涂层的应用范围和领域作了展望。     

大型油罐基础设计

结合100000m^3油罐基础设计，从基础必须适合上部构造特点要求出发，分析了大型油罐的基础结构构造特点及基础设计的主要方法，探讨厂大型油罐基础应该具备的技术性能及构造组成。     

核壳乳液聚合中甲基丙烯酸用量对印花制品的影响

采用核壳乳液聚合法合成涂料印花粘合剂，考察了甲基丙烯酸(MAC)用量的改变对印花产品的牢度和色光的影响：在核中，当MAC的用量分别为0．0g，0．2g，0．4g，0．6g时，干摩牢度分别为25，2．5 ，3,0，3．5，色光由暗变亮；在壳中当MAC的用量分别为0．0g，0.2g，0．4g，0．6g时，干摩牢度分别为2.5，2．5 ，3．0，3．5，色光变亮，对得色量和鲜艳度影响不大。     

蓄热室效能剖析

提高蓄热室效能是降低池窑能耗的有力措施.本文分析了反映蓄热室热交换能力的综合传热系数,进一步探讨了格子砖内部热交换过程和外部热交换过程中的矛盾以及解决矛盾的方法,继而谈及妥善处理在增加格子砖热交换表面上的矛盾,最后提出了衡量蓄热室效能的技术-经济指标以及提高技术指标的主要途径.     

液氨储罐保冷改造效果评定

作者结合实例，论述了氨罐保冷改造的设计、选材及施工，给出了改造后两年的测试结果，并对测试结果进行了分析。