Influence of process parameters on thermal-rate treatment of ZA42 alloy

Sand casting process and directional solidification technique combining thermal-rate treatment(TRT) were used. The influence of process parameters on TRT was investigated according to the values of impact toughness. At the same time, the mechanism of TRT was discussed. The results showed that TRT can improve the impact toughness of this alloy, while the hardness is basically constant. The time of heat preservation should not be more than 5min. Different forms of cooling intensification additive have different effects among which the zinc ingot solidified in graphite mold is the best one that can improve impact toughness of samples by more than 80%. With increasing the cooling temperature, the value of α(Al) crystal lattice constant increases. The element Sb has negative effect on TRT.     

4-methoxy-2,6-bis(3,5-dimethylpyrazoyl)-1,3,5-triazine modified carbon paste electrode for trace Cu(Ⅱ) determination by differential pulse volt-ammetry

A differential pulse voltammetric method was developed for the sensitive and selective determination of Cu(Ⅱ) at 4-methoxy-2,6-bis(3,5-dimethylpyrazoyl)-l,3,5-triazine modified carbon paste electrode in 0.05 mol/L KHC8H4O4 solution (pH = 4.02). The oxidation peak of Cu(Ⅱ) was observed at 0.065 V(vs Ag/AgCl) by scanning the potential in positive direc-tion. The analysis procedure consisted of an open circuit accumulation step in stirred sample solution. It was followed by medium exchange to a clean solution and subsequently an anodic potential scan was affected to obtain the voltammetric peak. The current was proportional to the concentration of the Cu(Ⅱ) ion in a range of 1× 10-7-1×10-4 mol/L for 6 min accumulation; the most of metal ions did not interfere with the determination. The developed method was applied to Cu(Ⅱ) determination in coal-ash sample, the results agreed with that of atomic adsorption spectroscopy(AAS).     

Cu-Al-Be形状记忆合金的应力腐蚀性能

用恒载荷法和慢应变速率法及SEM研究了Cu-Al-Be形 状记忆合金在甘油、海水和氨介质中的应力腐蚀性能.结果表明，Cu-Al-Be合金具有良 好的抗海水应力腐蚀性能和较低的氨介质应力腐蚀倾向.单相马氏体有较 好的耐海水腐蚀能力，可减少腐蚀引起的裂纹源；外应力下马氏体的孪晶变形和变体间的界 面迁移，则有利于松弛应力集中，阻碍和延缓腐蚀裂纹源的扩展，从而提高Cu-Al-Be合金的 应力腐蚀能力.     

Determination of heavy metals and volatile aromatic compounds in used engine oils and sludges

Assessment of contaminant releases during utilization of used oils is essential for the determination of environmental acceptability. These paper reports the results of the study examining a toxic metal leachability from used engine oil and sludge samples employing leaching test (TCLP). The leaching test indicated that lead in oil samples exceeded 5-ppm concentration level what qualified them as a toxic waste. The samples of contaminated sludge were found to contain high concentration of total lead, barium and chromium, but the leaching test showed concentration below regulatory limit. The total content of benzene, ethylbenzene, toluene, and xylenes (BETX), and naphthalene in used oil and sludge samples was also determined and was found not to be a significant factor to contamination.     

Gas—Liquid Mass Transfer Coefficient in Stirred Tank Reactors

Volumetric gas—liquid mass transfer coefficient (k_La) data available in the literature for larger tanks (T = 0.39 m to 2.7 m) have been analyzed on the basis of relative dispersion parameter, N/N_cd. It was observed that at a given superficial gas velocity (V_G), k_La values were approximately the same irrespective of geometric configuration (size of the tank, type and size of the impellers, type of the sparger, etc.) at a particular N/N_cd. A single correlation based on N/N_cd is presented which shows satisfactory agreement with the k_La data of different workers.     

螺旋藻多糖铁配合物制备、抗氧化及淋巴细胞增殖活性分析

以三氯化铁为原料,通过络合反应,对螺旋藻多糖(SP)进行结构修饰,制得有机铁化合物〔螺旋藻多糖铁(Ⅲ)配合物SP-Fe(Ⅲ)〕。采用FTIR、DSC、TGA、XRD和SEM对其结构进行了表征,采用DPPH(1,1-二苯基-2-三硝基苯肼)自由基法、羟自由基法等5种方法和MTT(四唑盐)法分析了SP和SP-Fe(Ⅲ)的抗氧化活性和淋巴细胞增殖活性的影响。制备的SP-Fe(Ⅲ)中Fe(Ⅲ)质量分数为16.42%±1.17%。采用5轴蛛网图对SP-Fe(Ⅲ)的抗氧化活性进行了综合评价。结果表明,SP-Fe(Ⅲ)相比SP具有较高的抗氧化活性。在模拟人工胃液消化后,随着消化时间的延长,在pH=6.8的人工肠液中释放出的Fe(Ⅲ)质量分数达到83.64%;在31.25×10–3 g/L的质量浓度下,与SP相比,SP-Fe(Ⅲ)配合物对淋巴细胞增殖提高了44.35%。     

Diffusion of additives and plasticizers in poly(vinyl chloride): 4. A programmed temperature technique for the determination of the diffusion parameters of three dialkylphthalates

A programmed temperature technique has been developed for the measurement of the self-diffusion coefficients of additives in polymers. This has been applied to the diffusion of three dialkylphthalate plasticizers in poly(vinyl chloride). Values of the self-diffusion coefficients and the calculated activation energies obtained in this way have been compared with values previously obtained from measurements at constant temperature. It has been shown that the programmed temperature technique gives a very rapid method for the estimation of the activation energy of self-diffusion.     

稳定态二氧化氯杀菌剂的制备及应用

稳定态二氧化氯(C1O2)是一新型杀菌消毒剂，具有高效、广谱、安全的特性，适用范围广，不产生对人体有害物质。介绍了稳定态ClO2的性质、检测、制备条件及其在有关领域的应用。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

旋风管内气相的湍流运动特性

利用二维激光多普勒测速仪(LDV)测量了旋风管内湍流运动的时均速度、脉动速度、能谱函数、微分尺度及湍流耗散等参数，对湍流特性参数分布进行了详细的描述，并初步分析了旋风管内湍流运动特性对颗粒分离的影响.