In situ regeneration of the Ni-based catalytic reformer of a 5 kW PEMFC system

The paper reports the results of on-site regeneration catalytic bed of the natural gas reformer in a 5 kW PEM fuel cell system. The Ni catalyst previously poisoned by sulphur from the available natural gas, could be re-activated by injection of pure water steam, following the method developed for industrial reformers using the same metal catalyst: this method was shown to be perfectly efficient, provided no natural gas was fed during the operation. Results of the tests conducted are presented and discussed in relation to published data on S-sorption on Ni surfaces.     

平面药包抛掷爆破的漏斗特征解析

根据惠州港通用码头陆域平面药包抛掷爆破的实爆堆积测量分析成果 ,结合药包设计的主要参数 ,对平面药包产生的爆破漏斗的范围与形态、不同药包部位的残方比与抛掷率、药包的长抗比与圆柱体药包的应力波形演变关系予以解析 ,供硐室爆破的理论研究、模拟试验和总结条形药包特性时参考     

广西某矿区托帕石的宝石学特征

广西某矿区的脉石矿物——黄玉分三个世代,其中第三世代的黄玉晶体无色透明,重量大于0.9克拉,瑕疵不明显,密度(3.50)、硬度(7.8430)和折射率(1.6330)等特征均达宝石级,经系统研究测试,可以命名为托帕石(Topaz)。     

锥形凸台成形的一种叠加滑移线场力学模型

分析了锥形凸台在不同体积成形工艺中的成形机理，基于模块化思想将锥形凸台的成形过程划分为挤压成形与角部充满两个特征时段；将上述两个特征时段的滑移线场力学模型有机联结，构建了锥形凸台成形过程的一种叠加滑移线场力学模型；介绍了叠加滑移线场力学模型的应力场与变形力的求解方法。该模型丰富了金属体积成形过程的特征单元库，可套用于局部成形的应力场与变形力求解，实现局部成形的模具优化设计。     

氧化锌颗粒膜电阻响应-恢复特性研究

测试了氧化锌颗粒膜电阻响应-恢复特性，讨论了颗粒形态，加热电压、环境气氛、气氛浓度和注入方式等因素对电阻响应-恢复特性的影响。结果表明，随着加热电压的升高，电阻响应-恢复的速度和程度明显加大；断续注入时颗粒膜电阻值的响应随着浓度的增加逐步减弱．     

Use of oxygen for the cleaning, passivation, and preservation of power-generating equipment at the Kharanorskaya SAPP

Studies conducted on two power-generating units at the Kharanorskaya SAPP relative to the steam-water-oxygen passivation, preservation, and partial cleaning of all boiler-heating surfaces, including the surfaces of the reheater, and passivation of the surfaces of the high-pressure heaters on the steam and water sides by the steam-oxygen method, as well as partial passivation, preservation, and cleaning of turbine blading are presented. __________ Translated from élektricheskie Stantsii, No. 6, pp. 56–64, May, 2006.     

A study on dynamic friction of different spun yarns

This article presents the results from a study of yarn-to-yarn (YY) and yarn-to-metal (YM) frictions conducted on ring, rotor, air-jet, and open-end friction (OE friction) spun yarns at different relative speeds and input tensions. The results indicate that the behavior of frictions for YY is different than that of YM. In case of YY friction, OE friction yarn shows maximum friction followed by rotor, air-jet, and ring spun yarns; however, a reverse order is noticed for YM friction. The relative speed and input tension have significant influence on the frictional behavior of spun yarns. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Cost effectiveness of decentralized energy supply systems taking solar and wind utilization plants into account

In this article, results are presented of annual simulations of a decentralized (regional) plant for the power and heat supply of a residential complex. This complex consists of four houses with 40 flats all in all. The annual power consumption of the complex is 157 MWh and the heat requirement is 325 MWh. The concrete dynamics of the energy demands over the year is taken into consideration. The energy supply system is composed of a power-controlled combined heat and power (CHP) plant (55 kW), a photovoltaic plant (PV array or PV plant) array for power generation as well as a field of solar thermal collectors with a short-term accumulator for water heating and a long-term accumulator for supplying heat for domestic heating purposes. Simulation results demonstrate that synergetic effects result from the combination of a CHP plant with wind power and PV plants of varying sizes, which have an effect on the cost effectiveness of the plant as a whole with the different dynamics of energy sources (wind and solar energies) and of the consumption of power and heat being the decisive factors. The power deficits of wind power and PV plants are compensated through the application of a natural gas-operated CHP plant. In almost all variants, the demand for fossil energy carriers is distinctly less than in conventional energy supply plants.     

Parametric circles and spheres

Formulations for parametric circles and spheres in terms of rational Gaussian (RaG) curves and surfaces are introduced. With the proposed formulations, a full circle is generated by interpolating a closed RaG curve to the vertices of an equilateral triangle, and a full sphere is generated by interpolating a closed RaG surface to the vertices of an octahedron with equilateral triangular faces. Generation of circles and spheres in this manner is very intuitive and easy to remember as the weights are all 1 and the nodes are all unique and uniformly spaced.     

油煤浆的管道输送特性与管路设计原则

通过理论分析和管道实验，探讨了油煤浆在工业管道输送中的流变特性、流动状态和阻力特性，得出了油煤浆的物性参数、表观参数、管道阻力参数的测定值和计算公式，并在此基础上探讨了油煤浆管道输送的设计原则，为油煤浆管路的设计提供基础数据、计算方法和一般原则。