用正交设计法优化导叶分段关闭规律的参数

本文介绍了正交设计法优化水轮机导叶分段关闭规律参数的方法，实例表明，此方法具有简单，准确和直观的优点。     

Performance of absorption refrigeration cycle at maximum cooling rate

The influence of irreversibility of finite-rate heat transfer on the performance of an absorption refrigerator is investigated using an endoreversible cycle model with continuous flow. The cooling rate is adopted as an objective function for refrigerator optimization. The maximum cooling rate and the corresponding coefficient of performance are derived. The optimal performance with respect to heat transfer areas of the refrigerator is analysed. In addition, certain significant conclusions are reached.     

Modeling and simulation of the drying of thin sheets in a continuous infrared dryer

The model gives the temperature and moisture distributions of the air, and of the moist sheet, as a function of time and distance in the dryer. The influence of the sheet's velocity and that of the radiant energy on the dryer performance as well as the effect of the moisture content of the entering sheet have been studied. A set of 27 experiments was carried out using the infrared dryer in order to calibrate the model. In these, the following three variables each had three operational levels: web velocity, initial web moisture and heating power. The model predictions agreed very well with the experimental data. Model predictions using arithmetic averages for the parameters, and parameters correlated with operational variables, are also presented and discussed.     

稀疏效应下一类捕食者与食饵系统极限环

研讨了稀疏效应下一类捕食者与食饵系统 :x· =x(x(r-x) -y) ,y· =b0 y(x -m) .讨论了该系统平衡点的性态 ,并证明了该系统极限环的存在性和唯一性 .     

我国力车胎行业现状与展望

介绍了2002年我国力车胎的行业现状。近年的发展及展望。并着重描述了力车胎专用设备的新发展。     

Integration of a Malt Drying Model into a Malt Plant Scheduling Software

Malting is a very intensive, energy-consuming process and, from the point of view of energy, green malt drying is one of the most important operations. Double-deck kiln drying, a variant of single-deck kiln drying, is the most commonly used process, but it is usually manually controlled under empirical control actions. These are the reasons why a research project was carried out based on the computer modeling of these process operations including a software tool named CIMFOOD. A knowledge-based system (KBS) allowing the entire processing-plant dynamic behavior simulation and scheduling concerning thermal energy requirements was developed.     

The Change of Body Temperature During Convective Drying of Cube-Shaped Apple Pieces

When using the convective drying method, the mass transfer between drying air and moisture diffusion of the material is very important. The moisture moves inside the material because of the volume change caused by the increased temperature. This movement is additionally affected by the texture of the material. According to the research dealing with colloid capillary porous texture of vegetables and fruit, the humidity migration inside the material occurs in both fluid and steam condition at the same time. This migration is stimulated by the heating and decreasing humidity along with the flow. In this research, winter varieties of apples (Jonathan, Golden Delicious, and Idared) were studied by heating of a 20 × 20 × 20 piece of apple with a thermocouple in it. On the basis of the measurements it can be stated that for the fruits with a high percentage of moisture (75-90%), when making the drying condition, the moisture gradient is influenced by the fractured cells of the cut area. It was found that the variety of apple is very important in relation to the heating and water loss gradient. According to the results, the wet volume change due to the heating highly influences the water loss. The models that describe the temperature of the material have a connection with the water loss.     

Comparison of Two Drying Schedules for European Hophornbeam (Ostrya carpinifolia Scop.) Lumber

Two types of conventional kiln-drying schedules (mild and harsh) based on moisture content (MC) were compared with regard to time, drying quality, and energy cost. The results were evaluated according to the classification of the European Drying Group. Proper drying periods of mild and harsh schedules were found to be 550 and 514 h, respectively. Evaluations in terms of drying quality indicated that better results were achieved with the mild schedule, especially when comparing drying defects and final MC. From an energy efficiency point of view, the harsh schedule, by saving 36 h of drying time, reduced electricity by 594 KWh and was therefore found to be $65 more profitable in this trial.     

A Mass Transport Model for Drying Wood under Isothermal Conditions

Mass transport in wood during drying can have different mechanisms at different periods of drying. Depending on the current moisture content (MC) and the structure of the wood, the driving forces for the mass transport are essentially different. Above the fiber saturation point (FSP), the lumens are partially saturated and the transport of liquid (free) water occurs as a consequence of capillary action. On the other hand, below the FSP, bound water within the cell walls is conveyed by diffusion, and water vapor in the lumens moves under influence of pressures gradient. Based on these considerations, a unified model is presented that takes into account the transport of the different moisture phases. Simulation of the drying of a Norway spruce sample at 50°C from about 135 to 7% MC is carried out using the finite element method (FEM). Comparison between the simulated average MC and the experimental observations obtained from X-ray computed tomography (CT) shows reasonable agreement. Possible simplifications in the model are briefly discussed as well as some aspects of the numerical implementation. Finally, the influence of absolute permeability on the average MC is studied.     

Manufacturing Drug Loaded Chitosan Microspheres by Spray Drying: Development, Characterization, and Potential Use in Dentistry

The aim of this work was to determine specifications for spray-drying manufacturing of sustained-release drug-loaded microparticles with potential application in dentistry. Chitosan was used as the microencapsulation polymer and ketoprofen as the model drug. A 1:1 chitosan/ketoprofen suspension was spray-dried under different operating conditions. The size distribution, morphology, total drug load, and release profile of the powders were characterized. In vitro release studies were performed with the powder samples entrapped in cellulose dialysis tubes. The microparticles produced had a narrow size distribution (mean diameter ranging from 2.11 to 3.27 µm), good sphericity, and a smooth surface. In vitro release studies showed a linear drug dissolution behavior.