采用纯化学物质校准仪器测定钛合金中碳量

采用纯化学物质对高频加热－红外检测碳硫仪校准，对钛合金中的碳量进行测定。     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

冷轧形变量对钛板材再结晶织构形成的影响

采用三维晶体学取向分布函数（ＣＯＤＦ）分析法研究了工业纯钛板材不同冷轧形变量对织构形成的影响。结果表明，冷轧形变量为５０－７０％时，再结晶退火后形成了（２１１８）（０１１０）和（１０１８）（１２１０）的部分纤维织构，而在３０％较低或８６％较高的形变量冷轧时，形成典型的轧制织构（２１１５）（０１１０）和再结晶织构（１０１３）（１２１０）型式。     

有水气藏开发早期可采储量的评价方法

有水气藏是天然气藏中的一个基本气藏类型，其采收率受多种因素的影响，如地面集输压力、井筒混合气水流动的液柱压力和储层物性等，目前普遍采用经验取值、物质平衡和气藏数值模拟等方法进行研究，但由于受开发评价阶段试采资料偏少和气藏数值模拟无法模拟井筒流动等因素的影响，早期采收率计算往往偏差较大，针对这些问题，从气田开发一体化的特点出发，提出了一种全面考虑地层→井筒→地面流动条件下，有水气藏（含凝析有水气藏）发废弃压力的计算方法，发展了利用物质平衡早期预测有水气藏采收率的理论，方法可靠、适用性强，能够推广应用。     

The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

钛铜复合棒及其标准化

概述了钛铜复合棒研制开发及发展历程,并介绍了钛铜复合棒的主要性能,以及钛铜复合棒的标准化情况。     

钛的应用及前景展望

从传统应用及新兴应用两方面对钛的应用进行了综述,并对钛的应用前景进行了展望。     

铁液洁净度对凝固热力学参数的影响

为了给高洁净钢连铸细晶技术提供相关理论依据，在高温钼丝炉中通过对电解纯铁加金属铝和硅脱氧，获得不同铁液洁净度的试样。利用差热分析法测定了试样在相同冷却速度下的过冷度。利用凝固过程热力学理论研究了铁液洁净度与过冷度、凝固热力学驱动力、形核功和临界晶核半径等的关系。结果表明：随着铁液洁净度的提高，铁液凝固时的过冷度增大，形核所需的凝固热力学驱动力变大，非均质形核功和临界晶核半径减小。     

热处理对Ti-25V-15Cr-2Al-2Mo-0.2C合金组织稳定性的影响

研究了热处理对Ti-25V-15Cr-2A1-2Mo-0.2C阻燃β钛合金组织稳定性的影响。结果表明，高温固溶并直接时效处理导致合金β基体上析出较多的α相沉淀，尤其在随后的热暴露组织中形成了恶化合金塑性的连续晶界α膜。然而，若在时效前再进行一次低温固溶处理则可明显减少α相的析出数量，合金的热稳定性因此而得到显著改善。