关于子母鱼雷的设想

概述了子母鱼雷这一新型鱼雷的设计基本依据的特点，论述了该鱼雷的作战使命与设计方案，叙述了发展子母鱼雷的必要性和可行性。     

Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

镀液中SiC含量和粒径对Ni-P-SiC复合化学镀层性能的影响

采用化学镀方法制备了Ni P SiC复合镀层 ,系统研究了镀液中SiC含量和粒径对镀层结构及显微硬度的影响。结果表明 ,镀层中SiC析出量随镀液中SiC含量的增加而增加 ,在SiC含量一定的情况下 ,当SiC粒径为 7.0 μm时 ,析出量最大 ;镀液中SiC的含量和粒度对原始镀层的硬度影响不大 ,但对 4 0 0℃热处理后的镀层硬度有显著影响     

拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。     

WC对铜基和镍基喷焊覆层材料耐气蚀性能的影响

在CuNiSiB,NiCrSiB自熔合金粉末中添加WC陶瓷颗粒，利用氧乙炔焰粉末喷焊工艺制备覆层材料，用超声波振动气蚀仪对覆层材料进行耐气蚀性能研究，用扫描电子显微镜对覆层材料表面气蚀破坏形貌进行观察，结果表明：复合覆层材料的耐气蚀能力比基体强；提高CuNiSiB覆层材料耐气蚀能力的途径是强化晶界，还探讨了覆层材料的气蚀破坏机理。     

电子封装用金属基复合材料的制备

分析了电子封装用金属基复合材料的性能特点及其对制备工艺的要求，在此基础上论述了该种材料的各种制备工艺的特点及发展现状。     

回旋管的应用研究

文章论述了推广回旋管应用中所碰到的高功率传输,模式变换和辐射尖锐的波束等技术难点,对现有的准光系统提出了改进措施。     

磁偏转电子枪研制核靶

文章叙述了磁偏转电子枪的原理和结构以及用ＥＱＤ－３型电子枪研制各种核靶的工艺过程。     

梯度折射率棒中传播的高斯光束轨迹解析解及其存在条件的讨论

本文提出光束轨迹方程的一般解，导出解析解的存在条件，推广了文献［１］的光线传播理论，文中以一特定梯度折射率棒为例，讨论了高斯光束在棒中的传播特性。     

镀镍云母导电复合材料的研究

对云母粒子化学镀镍及以LDPE为基材,镀镍云母粒子为填料制备的导电复合材料进行研究。认为此种导电复合材料只有质量轻、强度大及良好的导电等性能。