金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

Pyrolysis of tertiarybutylphosphine at low pressure

The pyrolysis of tertiarybutylphosphine (TBP) has been studied in the low pressure conditions used for chemical beam epitaxy (CBE). The pyrolysis studies were carried out in low pressure reactors of two different configurations, one of which is a cracker cell designed for use in a CBE system. The reaction products were studied using a quadrupole mass spectrometer. The products observed are accounted for by a reaction mechanism involving homolysis of the parent TBP molecule to produce PH₂ and C₄H₉ radicals. These undergo subsequent reactions to form the stable products C₄H₈, PH₃ and H₂, with smaller amounts of P and P₂ being produced. The production of the sub-hydride PH₂ using this cracker cell design indicates that the use of partially cracked TBP may be a promising technique for reducing the amount of carbon incorporated into the growing epitaxial layer.     

步进式加热炉炉温优化设定模型及软件开发

针对线材厂步进式加热炉实际工况，提出了基于经验规则的炉温优化设定模型和在线自学习获取知识的思想，并以炉温优化设定模型为核心，开发出加热炉计算机控制系统的优化运行软件。     

T_C≥400°C高温PTC陶瓷的研制

利用国产原料，采用传统的陶瓷材料制备工艺，研制了居里温度ＴＣ≥４００°Ｃ的高温ＰＴＣ陶瓷，制成了居里温度ＴＣ＝４１２°Ｃ，电阻Ｒ≤１０３Ω，ｌｇ（Ｒｍａｘ／Ｒｍｉｎ）＝４的高性能ＰＴＣ热敏陶瓷材料     

国际微电子专用关键设备的现状和发展趋势（考察报告）

讲述了参观Ｓｅｍｉｃｏｎ／ｗｅｓｔ９４′展览会及考察美国和西德的５个公司、１所大学所了解到的投影光刻技术、电子束曝光技术、透镜面形测试技术的发展。     

聚吡咯导电材料合成方法的进展

本文对聚吡咯及聚吡咯导电复合物的合成方法进行了综述。     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.     

锁相技术在电子束曝光机工件台稳速控制中的应用

采用锁相技术，对电子束曝光机工件台运动实现速度环的全数字控制。设计了数字差频积分回路和数字差频比例控制器，能有效消除速度的静态误差和改善系统的动态特性。     

ANALYSIS ON ROOM TEMPERATURE TENSILE STRENGTH OF δ-Al_2O_3, FIBER / Al-12Si COMPOSITE

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度δｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τＰ确定复合材料的ＲＯＭ预测曲线，应首先判断σｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论。