Microstructure and thermal behavior of Sn-Zn-Ag solders

The microstructure and thermal behavior of the Sn-Zn-Ag solder were investigated for 8.73–9% Zn and 0–3.0% Ag. The scanning electron microscopy (SEM) analysis shows the Ag-Zn compound when the solder contains 0.1% Ag. X-ray diffraction (XRD) analysis results indicate that Ag₅Zn₈ and AgZn₃ become prominent when the Ag content is 0.3% and above. Meanwhile, the Zn-rich phase is refined, and the Zn orientations gradually diminish upon increase in Ag content. The morphology of the Ag-Zn compound varies from nodular to dendrite structure when the Ag content increases. The growth of the Ag-Zn compounds is accompanied by the diminishing of the eutectic structure of the Sn-9Zn solder. Differential scanning calorimetry (DSC) investigation reveals that the solidus temperature of these solders exists at around 198°C. A single, sharp exothermic peak was found for the solders with Ag content less than 0.5%. Liquidus temperatures were identified with the DSC analysis to vary from 206°C to 215°C when the Ag content ranges from 1.0% to 3.0%     

酮亚胺对水性聚氨酯性能的改进

用丙酮分别和乙二胺、己二胺反应制备酮亚胺,并以其作为潜伏性扩链剂改善水性聚氨酯(PU)的性能。研究了酮亚胺以不同方式、加量对水性PU漆膜的厚度、硬度、耐水性、耐酸性、热稳定性和机械性能的影响。结果表明,采用丙酮缩乙二胺扩链的水性PU乳液的漆膜的耐水性优于用丙酮缩己二胺和用水扩链的PU乳液的漆膜,且加入过量的酮亚胺扩链效果较好,但其热稳定性并没有得到明显提高。     

Morphology of intermetallic compounds formed between lead-free Sn-Zn based solders and Cu substrates

The morphologies of intermetallic compounds formed between Sn-Zn based solders and Cu substrates were investigated in this study. The investigated solders were Sn-9Zn, Sn-8.55Zn-0.45Al, and Sn-8.55Zn-0.45Al-0.5Ag. The experimental results indicated that the Sn-9Zn solder formed Cu₅Zn₈ and CuZn₅ compounds on the Cu substrate, while the Al-containing solders formed the Al_4.2Cu_3.2Zn_0.7 compound. The addition of Ag to the Sn-8.55Zn-0.45Al solder resulted in the formation of the AgZn₃ compound at the interface between the Al_4.2Cu_3.2Zn_0.7 compound and the solder. Furthermore, it was found that the cooling rate of the specimen after soldering had an effect on the quantity of AgZn₃ compound formed at the interface. The AgZn₃ compound formed with an air-cooling condition exhibited a rougher surface and larger size than with a water-quenched condition. It was believed that the formation of the AgZn₃ compound at the interface occurs through heterogenous nucleation during solidification.     

中原高温高盐油藏疏水缔合聚合物凝胶调剖剂研究

针对中原油田高温(>80℃)、高盐度(>50 g/L)、高硬度(>1 g/L)砂岩油藏,研制了地下成胶的高热稳定性聚合物凝胶调剖剂。所用聚合物为疏水缔合聚合物AP-P4,M=9.0×106,HD=27%,疏水基摩尔分数0.2%;交联剂为可生成酚醛树脂的3种化合物;调剖剂胶液用矿化度160 g/L的马寨油田污水配制;实验温度95℃。根据形成的凝胶黏度(95℃,1.1 s-1)确定交联剂各组分用量为:MZ-YL 0.429%,MZ-BE 0.060%,MZ-XS 0.012%;酸度调整剂用量0.12%;成胶时间10~15小时。2.5、3.0、3.5 g/L AP-P4的凝胶在95℃老化100天后黏度保持在~40 Pa.s及以上。初配制胶液在3000 r/min下剪切15分钟后黏度降低87.5%~89.0%,但成胶后和老化过程中凝胶黏度只比未剪切样降低17.1%~6.6%。3.5 g/L AP-P4的调剖剂对~1μm2的6支储层岩心的堵塞率在88.1%~95.8%范围,平均93.3%,造成的残余阻力系数在15.2~28.6范围,平均19.8,使渗透率级差2.3~8.0的4组双人造岩心的注水流量比发生不同程度的反转。认为该凝胶调剖剂高温下稳定性好的原因,是强化学交联密度低,因而凝胶脱水收缩作用弱。图2表5参5。     

直齿圆柱变位齿轮的一种测绘方法

在工程实践中对损坏的无图纸齿轮进行重新制造时，测绘是必不可少的环节。在齿面已被严重磨损的情况下，如何准确地得到齿轮尤其是变位齿轮的各项参数是本文所着重讨论的问题。     

淀粉基干燥剂的化学性质与性能

讨论了淀粉、粗玉米粉及可以被淀粉所依附的纤维素框架的化学结构及性质,它们可能成为一系列用途广泛的干燥剂。     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

含有复合阻尼结构的压力波制冷机振荡管内流动分析

通过对含有复合阻尼结构的压力波制冷机振荡管内的流场分析，详细讨论了激波在接受管内的行为，数值计算同时表明：含有两道复合阻尼结构加上激波吸收腔完全可以将激波降低到工程上可以接受的程度。     

Study on Preparation and Application of Ti／Si Complex Zeolite

A Ti/Si complex zeolite has been prepared. X-ray diffraction and infrared spectrometry study has shown that two structures, namely the ZSM-5 and MCM-41, exist in the sample. BET tests have revealed that the complex zeolite contains regular mesopores of 2.6 nm. Ultraviolet spectrometry analysis has shown that the Ti species exist in the zeolite skeleton in the form of tetra-coordinate valence. The Ti/Si complex zeolite (TS-1/Ti-MCM-41) has apparently improved catalytic activity with respect to the macromolecular organic compound oxidation as compared to individual components of either Ti or Si containing zeolites (TS-1 and Ti-MCM-41).