Fuzzy Multiobjective and Linear Programming Based Management Models for Optimal Land-Water-Crop System Planning

In this article, linear programming and fuzzy optimization models are developed for planning and management of available land-water-crop system of Mahanadi-Kathajodi delta in eastern India. The models are used to optimize the economic return, production and labour utilization, and to search the related cropping patterns and intensities with specified land, water, fertilizer and labour availability, and water use pattern constraints. Due to extreme backwardness of the study area, it has been decided to keep all the three objectives of the linear programming models at the same priority level to obtain the compromised solution in a fuzzy environment that incorporates the imprecision in fuzzy goals and fuzzy constraints. These non-structural models facilitate the conjunctive use of available surface water and groundwater resources. A comparative evaluation along with the benefit-cost ratios of the existing and proposed farming systems is also presented.     

Study on Hot Deformation Cracks of Steel D2 Using Procesing Map

ＳｔｕｄｙｏｎＨｏｔＤｅｆｏｒｍａｔｉｏｎＣｒａｃｋｓｏｆＳｔｅｅｌＤ２ＵｓｉｎｇＰｒｏｃｅｓｉｎｇＭａｐＧａｏＳｈａｎ，ＬｉｕＸｉａｎｇｈｕａ，ＷａｎｇＧｕｏｄｏｎｇＡＢＳＴＲＡＣＴＴｈｅｈｏｔｄｅｆｏｒｍａｔｉｏｎｂｅｈａｖｉｏｒｓｏｆｓｔｅｅｌ...     

自动线性跟踪Butterworth有源滤波器研究

滤波是通信、测试、数据采集和实时控制等领域至关重要的环节。通常的模拟滤波器，由于截止频率固定，在某些宽频率动态范围且有实时性要求的应用场合，往往达不到预期的滤波效果，有时甚至影响整个系统的正常运行。本文从有源滤波器的机理分析入手，提出了一种由单片机参与的滤波系统，它能自动跟踪输入信号频率，线性地选择合适的滤波器截止频率，弥补了原有滤波器的不足。     

本钢炼焦煤最佳配比分析

结合本钢的生产实际，对炼焦煤的最佳配比作了比较具体的分析，同时对资源，质量、成本也作了比较详细的调查，并提出了本钢焦化厂最佳配煤比方案，由此可看出，最大限度地降低采购成本，继续开发合理的配煤比例，具有广阔的前景。     

煤气吹扫时惰性气体抑爆用量的优选

运用惰性气体消防抑爆理论，采用数学积分法计算出吹扫煤气设施时抑爆所需最少惰性气体需要量．     

阳平关砂金矿精选厂尾矿综合回收的研究

本文详细的介绍了陕西省阳平关砂金矿精选厂尾矿金和其他可利用的矿物综合回收方法和最佳分选流程。     

高效率平面磁控溅射器的研制

介绍一种新型磁控溅射装置。它采用两块极性相对的环状磁铁的设计方法，通过扩大靶表面的等离子放电区域面积，使传统磁控溅射枪使用中经常受到的两个限制──溅射速率与靶的利用率得到了较大的改善。实验中铜靶在溅射功率密度为11W／cm~2时溅射速率约为800nm／min，如果继续提高功率则可获得更高的速率。而靶的利用率可达64％左右。另外，在认为出射粒子符合cos~nθ分布的前提下，发现当n＝3．3时，实验数据和理论数据符合得较好。     

无线电引信被干扰率及抗干扰率

本文从无线电引信相对杀伤比率出发，引伸出引信被干扰率及抗干扰率的定义及计算公式。     

Corrosion fatigue short crack growth behaviour in a high strength steel

The influence of an aggressive environment (0.6 M, aerated NaCl solution) on short fatigue crack initiation and growth behaviour has been studied. The study involved three major test series, namely: air fatigue, corrosion fatigue, and intermittent air fatigue/corrosion fatigue. The above tests carried out under fully reversed torsional loading conditions at a frequency of 5 Hz, showed that it was the non-metallic inclusions which took part in crack initiation resulting from debonding at metal matrix/inclusion interface and pitting of inclusions in both air and corrosove environments, respectively. Short fatigue crack growth results in these two environments obtained by using plastic replication technique, indicated a large effect of microstructure i.e. prior austenite grain boundaries. The stage/stages at which the environmental contribution was dominant has been discussed by considering the results achieved from intermittent tests. However, the mechanisms involved in corrosion fatigue short crack growth have also been described in the light of results obtained from futher investigations carried out by conducting corrosion fatigue tests under applied cathodic potential conditions and tests on hydrogen pre-charged specimens under air fatigue and uniaxial tension conditions.