Structure and properties of polyimide‐bonded magnets processed from prepolymers based on diacetyl derivatives of aromatic diamines and dianhydrides

We report a novel method of polyimide (PI) synthesis from prepolymers based on dianhydrides and diacetyl derivatives of aromatic diamines that facilitate the preparation of a melt processable mixture at 300 ± 10°C of the prepolymer and magnetic Nd‐Fe‐B alloy to provide PI‐bonded magnets with enhanced properties. It is shown that chemical structure of the prepolymers strongly influences viscosity behavior via crystallization of the oligoimide in the melt, leading to formation of PI with rigid‐rod like structure. This structural ordering of the prepolymers based on diacetyl derivative of diamine used in this study, if not controlled, leads to exponential increase of melt viscosity with time, making it practically impossible to prepare melt processable mixture of the magnetic particles and the PI prepolymers at elevated temperatures. The results obtained demonstrate that appropriate dianhydrides and diacetyl derivatives of diamines that do not lead to crystallization of oligoimides in prepolymer mixture can be used under controlled processing conditions to prepare melt‐processable PI‐bonded magnets containing rigid‐rod like PI structure that significantly increases thermal stability of the magnets. The temperature dependencies of the magnetic properties of the PI‐bonded magnets under conditions that they are likely to encounter during their service life were found to be remarkably similar to that of commercial thermoplastic magnets such as injection‐molded nylon magnets. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 478–485, 2006     

An analysis,design and tuning of Cascade Control Systems in the presence of constraints in actuator and process outputs

In the presence of rate constraints in actuator, design of cascade controller based on the primary controller conditional integration can result into closed-loop system oscillations. Stability analysis, performed by the describing function technique and confirmed by simulation, demonstrates that the solution based on the Anti-Reset Windup Cascade Control System (ARW CCS) structure is successful. Design and tuning of the ARW CCS secondary controller is a standard ARW single-input single-output problem. In the present paper tuning is proposed for the ARW CCS primary controller. For the serial process modeling simple rules are derived and confirmed by experimental results, obtained on a drum type boiler of a 210 MWe lignite coal fired unit. General design of the ARW CCS is based on the parallel process modeling and optimization of the primary controller. Optimization is performed in the frequency domain, under constraints on the maximum sensitivity, multiplicative uncertainty bound and sensitivity to measurement noise. Simulation and experimental results on a laboratory thermal plant demonstrate effectiveness of the proposed optimization.     

高效液相色谱法测定稻·恶乳油中稻瘟净和恶霉灵的含量

本文采用高效液相色谱法 ,对稻瘟净和恶霉灵的复配制剂进行分析 ,色谱柱 2 5 0mm× 4 6mm不锈钢柱 ,内装BDSC18填充物 ,检测波长 2 2 0nm ,流动相 :乙腈 +水 =6 0 +4 0 (v/v) ;回收率 :稻瘟净 99 5 %～ 10 0 5 % ,恶霉灵 99 3%～ 10 0 6 % ,变异系数分别为 :0 41%和 0 6 9% ,为稻 恶乳油产品的质量控制建立了准确、快速的分析方法     

浅谈信息技术教育在艺术设计专业中的应用

当今社会已进入信息化时代,作为美学和功能学相结合的艺术设计专业,与发展迅猛的信息技术相结合是顺应时代发展的必然现象,信息技术为艺术设计提供了新的技术支撑和思维模式,大大促进了教与学的优化与提升,更好的培养和提高了学生的信息素质,从而使艺术设计从业人员创作出更能符合受众者所需的艺术设计作品。     

我国高等学校法人治理结构的实施框架

高等学校法人治理结构的关键在于权力分配与权利制衡,目标在于真正落实高等学校的办学自主权。只有以现存的治理制度与组织结构为基础,引入现代企业治理结构和国外高等学校法人治理的经验,对高等学校的科层制管理结构进行改良,建立符合我国国情的高等学校法人治理结构,才是落实办学自主全权,完善自我管理的必要出路。     

Possible Energy Network with polygeneration system and CCS for China

On basis of adopting polygeneration systems for power and alternative fuels,capturing CO2 with near zero energy penalties,and storing CO2 on sites,a new kind of Energy Network can integrate energy utilization,CO2 capture,transportation and storage synthetically.Techno-economic analysis of this solution focusing on Inner Mongolia and the Yangtze River Delta districts had been carried with comparison to the chain method for energy utilization and CO2 sequestration.This solution can save 21.5% of energy,and re...     

Application of open-pit and underground mining technology for residual coal of end slopes

Given the conditions of residual coal from the boundary of a flat dipping open-pit mine,which uses strip areas mining and inner dumping with slope-covering,we propose an open-pit and underground integrated mining technology for residual coal of end slopes.In the proposal a conveyance road and ventilation conveyance near the slope are built,corresponding to the pit mining area and the surface coal mine dump,as well as an interval haulage tunnel and air-inlet tunnel.The outcome shows that such mining method may reduce the effect to slope stability from underground mining,it does not affect the dumping advance and has a high recovery rate of residual coal resources.The working face is timbered by single hydraulic props,transported by a scraper conveyor and supported by coal walls.This method of mining is one of layered top coal caving,with high resource recovery,low production cost where positive economic benefit can be realized.     

Deformation and failure study of surrounding rocks of dynamic pressure roadways in deep mines

In order to understand the change rules of stress-displacement in surrounding rocks of dynamic pressure roadways in deep mines and to obtain a theoretical basis for analyses of roadway stability and designs of support,we established a coupling equation of adjacent rock strength,mining stress and supporting resistance on the basis of an elastic-plastic theory of mechanics.We obtained an analytical solution for stress and displacement distribution of elastic and plastic regions in surrounding rock of dynamic pressure roadway..Based on this theory,we have analyzed the changes in stress-displacement in elastic and plastic regions of surrounding rocks of dynamic pressure roadways in the Haizi Coal Mine.The results show that:1) radial and tangential stress change violently within the first 4 m from the inner surface of a roadway after excavation;radial stress increases while tangential stress decreases within a range of about 6 m from the inner surface of the roadway as a function of q3;2) radial and tangential stress increase with an increase in the mining pressure coefficient k;the increase in the rate of tangential stress is greater than that of radial stress;3) the radial displacement of the inner surface of roadways decreases with an increase in q3,provided that k remains unchanged.     

多重网格法在地球物理正反演应用研究中的进展

现阶段地球物理三维勘探面临越来越复杂的问题,其要求更精细的三维网格剖分,现有的一些方法随着网格节点的增加其收敛速度相应减慢。对于应用中更复杂实际模型、更细密网格剖分以及更快收敛速度要求,难于有进一步提高。要有所突破,需借助计算数学最新进展,引入新的高效算法。多重网格法是近二十年迅速发展的一种求解微分方程近乎最优的新算法。本文首先简单介绍了多重网格法基本原理和运算格式,着重介绍了当前国内外多重网格法在地球物理正反演中的应用成果和发展现状。此外,对多重网格法在地球物理正反演中的应用前景及发展趋势进行了展望。     

Damage and deterioration mechanism and curing technique of concrete structure in main coal cleaning plants

Concrete structures in main coal cleaning plants have been rebuilt and reinforced in the coal mines of the Shanghai Da-tun Energy Sources Co. Ltd., the first colliery of the Pingdingshan Coal Co. Ltd. and the Sanhejian mine of the Xuzhou Mining Group Co. Ltd. In these projects, the operating environment and reliability of concrete structures in the main plants of the three companies were investigated and the safety of the structures inspected. Qualitative and quantitative analyses were made on the spe-cial natural, technological and mechanical environments around the structures. On the basis of these analyses, we discuss the long-term, combined actions of the harsh natural (corrosive gases, liquids and solids) and mechanical environments on concrete structures and further investigated the damage and deteriorating mechanisms and curing techniques of concrete structures in the main coal cleaning plants. Our study can provide a theoretical basis for ensuring the reliability of concrete structures in main coal cleaning plants.