泡沫陶瓷的研制

泡沫陶瓷是一种新型的功能陶瓷材料。它具有独特的结构和性能，在工业中有着广泛的应用前景。泡沫陶瓷具有密度小、透气性高、耐高温、抗化学腐蚀等特性。本研究对用颗粒强化的氧化铝骨架合成泡沫陶瓷进行了分析。这种材料比其它多孔陶瓷材料具有更好的热化学性质。这种材料可以用有机海绵浸浆获得，然后烧去海绵，留下多孔陶瓷网。这种方法的优点是它包含了过程参数和陶瓷结构，同时合成物的烧结情况及其它条件的影响在文中也有阐述。     

气流床水煤浆气化技术的应用现状及开发进展

气流床水煤浆气化是煤高效、洁净利用的一项关键技术。简述了具有代表性的气流床水煤浆气化技术的应用现状及开发进展,并分析了影响水煤浆气化的主要因素,如烧嘴、耐火砖、进料系统、激冷环等,提出了一些改进措施。     

PPS泥浆法预浸技术的研究

本文介绍了一种新型的，用于热塑性树脂基复合材料的泥浆法预浸技术，该工艺具有对纤维损伤小，不污染环境和树脂含量容易控制等优点，本文重点讨论了了该工艺的关键技术－ＰＰＳ（聚苯硫醚）泥浆的制备技术及其预浸工艺?     

淤浆法HDPE装置低聚物不能结片原因探析

分析了淤浆法HDPE装置低聚物不能结片的原因,并提出了相应的工艺处理措施。     

Al2O3／TiB2／SiCW陶瓷刀具加工镍基合金时的磨损机理研究

研究了Ａｌ２Ｏ３／ＴｉＢ２／ＳｉＣＷ陶瓷刀具加工Ｉｎｃｏｎｅｌ７１８镍基合金时的切削性能和磨损机理。结果表明；在低速切削条件下，Ａｌ２Ｏ３／ＴｉＢ２／ＳｉＣＷ和硬质合金刀具的抗后刀面磨损的能力相差不大；而在高速切削条件下，前者的抗后刀面磨能力远高于后者。     

造纸黑液制水煤浆添加剂成浆性能的研究

针对淮化德士古气化炉所用的义马煤和鲁南化肥厂使用的配煤 ,进行了造纸黑液制添加剂实验室和工业制浆性能的考察。结果表明 ,其在工业应用中的添加量范围在 1.2 %～ 1.6 % (浆基 ,添加剂含固量 2 0 % ) ,对义马煤和鲁南配煤分别可以制出浓度在 6 4 .5 %和 6 9%之间 ,稳定性能良好 ,满足工业生产要求的水煤浆     

掏槽法在黄麦岭磷矿掘双壁沟爆破中的应用

在黄麦岭磷矿露天开采的掘沟爆破中，根据掏槽法的机理，使用大孔径深孔掏槽，采用多排微差挤压爆破，一次形成开采所需的双壁沟，提高了掘沟效率，扩大了掏槽法的应用范围。     

Rheological studies on a slurry biofuel to aid in evaluating its suitability as a fuel

Biomass is an often abundant, renewable, low ash and low sulfur fuel. Due to these properties, biofuels are promising alternatives for traditional petroleum-based fuel applications; however, traditional biofuels for internal combustion engines are not cost competitive with gasoline, diesel or fuel oils. One method to reduce the cost of biofuels is to use slurry fuels which have a potential lower cost than liquid biofuels due to high conversion efficiencies. Slurry biofuels, such as a mixture of corn and water, could provide a biofuel alternative for diesel engines, pressurized gasifiers and heating oil applications such as burners or gas turbines. Use of these biomass slurries poses important questions about their stability and suitability for practical applications in internal combustion engines and combustors.This work reports rheology data for stable corn-starch water slurries (CSWS) which used a polyacrylic acid thickener to eliminate settling of the slurry and to provide desirable shear-thinning behavior for most of the compositions evaluated. The effect of shear rate on the viscosity of the CSWS was studied using a BOHLIN-controlled stress (CS) rheometer. The well-known Ostwald—de Waele power law and Sisko models for viscosity fit the data. The effect of corn starch content, thickener content and temperature on the viscosity of CSWS was also studied. The favorable shear thinning properties were observed for starch contents up to 45% starch and should aid pumping, injection and spraying. The lower heating values of the slurries, however, are undesirably low.     

Strong dependence on pressure of the performance of a Co/SiO2 catalyst in Fischer–Tropsch slurry reactor synthesis

A 10 wt% Co/SiO₂ catalyst was prepared by the incipient wet-impregnation method and tested in Fischer–Tropsch synthesis in a slurry reactor under conditions approaching industrial practice. The catalyst precursor was investigated by X-ray diffraction (XRD), temperature-programmed reduction (TPR), transmission electron microscopy (TEM) and photoelectron spectroscopy (XPS). The XPS and XRD techniques revealed the presence of a crystalline Co₃O₄ spinel-type phase, while-in addition-TEM and XPS analyses pointed to the formation of another amorphous Co₃O₄ spinel phase, both species interacting weakly with the silica substrate. The influence of total pressure on the conversion, selectivity and stability of the catalyst was studied. Upon increasing the overall pressure from 20 to 40 bar, not only activity increased but also the catalyst are not deactivating. These results are explained in terms of an increase of gases solubility in the solvent, this increment of CO concentration in the liquid phase favours carbonyl species formation and the cobalt particles segregation that implies an increase in the metal surface area.     

Analysis of pentasodium triphosphate hydration kinetics

The present work analyzes the effect of various factors on the hydration of pentasodium triphosphate. The experimental method is based on application of the hydration test. Technical-quality products with different proportions of phase I and phase II have been used. The variables studied are phase I/phase II ratio, initial temperature, particle size, stirring rate and composition of the slurry (presence of hexahydrate crystals and water hardness). The results have been discussed according to a kinetics model that includes a series of stages of a physical nature (dissolution of anhydrous salt and the crystallization of the hexahydrate), as well as of a chemical nature (solvation of the ions in solution). Crystallization of the hexahydrate may be the controlling stage in the process.