基于振动实测的非均质地层钻头失效分析与对策

四川盆地作为国内页岩气开发的重点区域,通过近几年的不断攻关和实践,机械钻速得到了提高,但由于受地层复杂、可钻性差、非均质性强等地质因素的影响,导致井下钻柱系统不良振动剧烈,容易出现钻头损坏严重、钻速较低等问题,严重影响了钻井时效。为了解决上述难题,以该盆地涪陵工区上二叠统龙潭组—中二叠统茅口组为例,采用井下振动高频测量工具的实测手段,测量了钻头—钻柱系统的动态振动加速度参数,结合地层的岩性和矿物组分分析,研究钻头失效原因与对策,并开展了现场试验。研究结果表明:①在非均质地层中钻进的钻头—钻柱系统产生了大于40 m/s~2的高幅值瞬时冲击振动,高幅值的瞬时冲击是导致钻头先期失效的主要原因;②提出了抑制高幅值的瞬时冲击振动采用"减振+增压"工具组合和避免井下工具共振的钻井参数;③采用钻井新参数的试验井比邻井的高幅值瞬时振动降低了17%,单只钻头进尺增加24%,钻头工作环境得到了较大的改善,钻头使用数量减少。结论认为,该研究成果能够有效地改善钻头—钻柱系统的振动状态,有利于达成延长钻头使用寿命的目标。     

Assessment of local strain field in adhesive layer of an unsymmetrically repaired CFRP panel using digital image correlation

The present study focuses on experimental investigation of through the thickness displacement and strain field in thin adhesive layer in single sided (unsymmetrical) patch repaired CFRP (carbon fiber reinforced polymer) panel under tensile load. Digital image correlation (DIC) technique is employed to acquire the displacement and strain (longitudinal, peel and shear) field. Experimental determination of shear transfer length based on shear strain field obtained from DIC is introduced to estimate the optimum overlap length which is an essential parameter in patch design for the repair of CFRP structures. Further, DIC experiment with magnified optics is performed to get an insight into complex and localized strain field over thin adhesive layer especially at critical zones leading to damage initiation. The failure mechanism, load displacement behavior, damage initiation and propagation are closely monitored using DIC. The influence of patch edge tapering on strain distribution in adhesive layer is also investigated. The DIC successfully captures the global and localized strain field at critical zones over thin adhesive layer and further helps in monitoring the damage based on strain anomalies. Strains are found to have maximum magnitude at the patch overlap edge and the shear strain level in adhesive layer is higher than the peel strain. Normal tapering increases the peel strain and has negligible influence on shear strain level in adhesive layer. The recommended overlap length is found to be consistent with the recommendation in the literature. Whole field strain pattern and the overlap length obtained from experiment are further compared with the finite element analysis results and they appear to be in good coherence.     

Simultaneous accommodation of Dy3+ at the lattice site of β-Ca3(PO4)2 and t-ZrO2 mixtures: Structural stability,mechanical, optical,and magnetic features

Structurally stable β-Ca₃(PO₄)₂/t-ZrO₂ composite mixtures with the aid of Dy³⁺ stabilizer were accomplished at 1500°C. The precursors comprising Ca²⁺, P⁵⁺, Zr⁴⁺, and Dy³⁺ have been varied to obtain five different combinations. The results revealed the fact that complete phase transformation of calcium-deficient apatite to β-Ca₃(PO₄)₂ occurred only at 1300°C, whereas the evidence of t-ZrO₂ crystallization is obvious at 900°C. The dual occupancy of Dy³⁺ at β-Ca₃(PO₄)₂ and t-ZrO₂ structures was evident; however, Dy³⁺ initially prefers to occupy β-Ca₃(PO₄)₂ lattice until its saturation limit and thereafter accommodates at the lattice site of ZrO₂. The typical absorption and emission behavior of Dy³⁺ were noticed in all the systems and, moreover, the surrounding symmetry of Dy³⁺ domains has been determined from the luminescence study. All the systems ensured paramagnetic response that is generally contributed by the presence of Dy³⁺. A gradual increment in the phase content of t-ZrO₂ in the composite mixtures ensured a significant improvement in the hardness and Young's modulus of the investigated compositions.     

垦71井区三维VSP资料波场分离方法应用研究

三维VSP资料是多偏移距VSP资料，资料中多种类型的波叠合在一起形成复杂波场。从复杂波场中分离出单一的保幅反射波波场是三维VSP波场分离的重要工作。常规二维VSP波场处理方法单一，难以适用于复杂的三维波场处理。针对三维VSP资料的波场特点，以分离上行反射P波为例，将单一波场分离方法加以适当组合，对垦71井区三维VSP实际资料进行了应用研究。结果表明，波场分离处理中叠加消去法和中值滤波相结合以及F—K滤波和中值滤波相结合的方法克服了单一方法的缺陷，波场处理后获得了波组特征明显、波场清晰单一的上行反射P波保幅波场，取得了较好的波场分离效果。     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

复合材料的最新进展与应用

叙述了复合材料的发展概况 ,详细介绍了增强材料的种类、性能、形式及加工技术 ,指出了复合材料具有广阔的应用前景     

Ni-Al2O3纳米复合电镀工艺的初步研究

初步研究了复合电镀各工艺条件：电流密度、镀液pH值和温度以及搅拌方式对Al2O3纳米微粒在镍基复合镀层中含量的影响。研究表明：电流密度增大不利于提高镀层中纳米微粒的含量；pH值增大也明显使复合量降低;镀液温度升高，镀层中微粒的复合量随之略有改变；电镀时，加强搅拌或适当改变搅拌方式，可以使复合镀居中的纳米微粒含量提高。还利用扫描电镜及能谱对Ni-Al2O3镀层表面进行了观察与分析。     

陶瓷及陶瓷基复合材料微缺陷的超声检测

为研究陶瓷及陶瓷基复合材料微缺陷的超声检测能力，针对一些人工缺陷试样进行了超声检测试验。试验主要采用了纵波垂直入射法和泄漏瑞利波法。通过试验结果，比较了两种方法的检测能力。     

负载型复合载体及其镍基催化剂的性能

采用溶胶-凝胶法制备了负载型ZrO_2/Al_2O_3和ZrO_2/Al_2O_3-SiO_2复合载体,研究了不同复合载体对Ni基催化剂CO_2重整甲烷反应和性能的影响,并用XRD、IR、TPR、TPD和BET等方法对复合载体及催化剂进行了表征。结果表明,ZrO_2负载在基载体后比表面积、碱性、活性组分Ni的分散度和Ni与ZrO_2的相互作用增大。NiO在复合载体表面的分散容量与ZrO_2的负载量有关,ZrO_2的负载量为37．5%时NiO的分散容量达最高值(24．0%)。与Ni/ZrO_2相比,Ni/ZrO_2/Al_2O_3-SiO_2和Ni/ZrO_2/Al_2O_3催化剂对CO_2的吸附能力增大,CO_2吸附量增加,酸强度降低,CO_2重整CH_4反应活性提高,其中以Ni/ZrO_2/Al_2O_3催化剂的活性最好。     

反转构造的反转程度及其与油气聚集的关系

结合典型反转构造地震剖面，分析了断层型和褶皱型两类反转构造的反转程度，上下皆正断层型和向形褶皱型反转构造的反转程度轻微；上逆下正断层型和透镜形褶皱型反转构造的反转程度中等；上下皆逆断层型和背形褶皱型反转构造的反转程度强烈。分析了反转构造的反转程度与油气聚集的关系，处于轻微反转程度的上下皆正断层型反转和向形褶皱型反转，以及处于强烈反转程度的上下皆逆断层型反转和背形褶皱型反转不利于油气聚集；处于中等反转程度的上逆下正断层型反转和透镜形褶皱型反转类型有利于油气聚集成藏。