Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

The thermal ignition of lignocellulosics in infinite slab and cubic geometries

Wood shaving samples were heated in both cubic baskets and in a previously described system realising the conditions of the ‘infinite slab’ in thermal ignition. Results from the two sets of experiment were found to be totally consistent with each other.     

Study on ASTM E399 and ASTM E1921 standards

Costs of ASTM E399 and ASTM E1921 tests, which were developed to determine the fracture toughness (K_Ic) and the ductile–brittle transition temperature of ferritic steels, respectively, are considered high and the procedures are also very complicated. In this study, a method, which is more cost‐effective and easier to carry out, is proposed.     

Sicherer und wirtschaftlicher Betrieb von Kraftwerken – Ergebnis der Forschung im Bereich Werkstoffe,Auslegung und Instandhaltung

Safe and Economic Operation of Power Plants – Research Results in the Field of Materials, Design and Maintenance Components of power plants which undergo high temperatures are subjected to complex loading situations. The requirements on the used materials result from the special operation conditions of the plants and have to be adjusted to the steadily growing requirements on higher efficiency of the complete power plant as well as to those of safe and economic operation. The expenses for control and downtimes are directly connected with economic efficiency and availability. However, in case of new procedures or components it is not possible to revert to the existing know‐how. Different failure mechanisms than known before can occur. The same goes for the load situation. Therefore the knowledge base has to be extended to in‐advance or even parallely running scientific examinations that life assessment and maintenance strategies can be applied which guarantee the operational reliability and the efficiency of the plant. The main emphasis of these F&E works has to be put on condition monitoring based on actual operational data, the standard materials’ and component’s behaviour (deformation, damage and failure behaviour) in connection with design of components and the related material laws. In the framework of applied AVIF projects, following problems are handled:. – qualification of materials by determinating parameters related to practise. – optimal design of components by making available material laws and numerical tools. – economic manufacturing of components by qualifying processing methods such as welding. – The results can be transferred to concepts for safe and economic operation of power plants, especially for newly introduced materials for which there is no operational experience available.     

马鞍山煤矿瓦斯地质理论在防突工作中的应用

总结了实际工作中防突管理的经验和问题 ,探讨了科学理论与具体实际的有机结合与统一 ,采取针对性强的有效措施 ,确保突出矿井的安全生产