金线断口的分析

运用扫描电子显微镜技术，对金线断口观察分析，讨论金线在拉伸过程中断裂时断口形貌及断裂的原因，发现，断裂是由于金锭中的气体和杂质引起的，并提出改进生产工艺的意见。     

溢流反弧段水流边界层有关概念的探讨

本文对溢流反孤段水流边界层的定义方法进行分析讨论。在分析及弧段流速分布的基础上提出离心力附加边界层厚度和粗糙度附加边界层厚度的概念,研究了壁面曲率和壁面粗糙度对溢流反弧段边界层发展的影响。     

初级金属固溶体的固相线

本文提出二元合金A_(1-x)B_x的初级金属固溶体的固相线的计算公式为:T_m(x)=T_(mA)F(x),其中T_(mA)是A金属的熔点,F(x)是以X为变量、包含A和B的原子密度N、价数Z、熔化体积增率(△V/V)和熔化熵△S的解析函数.对于以Cu、Ag、Au为基的、包含一价到四价的简单金属的24种初级金属固溶体的固相线作了理论计算.与实验结果符合较好.对于三元合金也作了相应的推广.     

结构强度储备的评估及结构维修过程的跟踪决策

本文提出了已建成结构在服役过程中构件的强度储备比和结构整体的强度储备比的概念和定义,它们都是随结构使用和维修过程而变化的时间的函数。我们建议以实际的强度储备比作为构件和结构服役安全度的表达方式,给出了构件和结构强度储备比的具体评定方法,并以结构整体的强度储备比作为控制参数决策结构的维修过程,以求得结构全寿命维修的优化控制。本文所提出的方法适用于具有良好的结构重分析程序和精密细致的检测手段的工程。一般重要的结构工程,例如核电站、海上结构、航空航天设备等均具备上述条件。因而本文所提的方法非常实用,可以立即应用于重要的工程项目,具有重大的经济和社会效益。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

PAN共聚纤维的热氧化研究

本工作采用连续式实骏装置与方法,借助力学测试、X射线衍射、元素分析、红外光谱等技术,系统地研究了PAN共聚纤维在连续热氧化过程中化学、结构、性能间的联系,亦对PAN基碳纤维力学性能提高的途径进行了探讨。研究结累表明:在热氧化过程中,PAN共聚体系的热化学反应主要发生在250℃左右;其间纤维的序态结构变化剧烈,易使纤维产生结构缺陷,进而影响热氧化纤维力学性能的变化。     

球铁管表面喷锌机的设计与研究

球铁管是我国“九五”和“十五”期间大力推广和发展的项目 ,在大量的设计和应用基础上 ,对球铁管生产使用的重要设备之一———表面喷锌机进行了系统的研究与分析 ,提出了相关的设计思想和方法。对于提高表面喷锌机的使用性能和生产效率具有重要意义     

平衡纵剖面数值试验及其对防洪的影响研究

本文采用一维非恒定流非均匀沙的水沙数学模型，以长江中游螺山汉口河段为背景，进行了根化数值模拟试验，分析了该概化河段平衡纵剖面的变化规律及其与上游来水来沙条件的关系，并和相应的理论公式进行了比较。在此基础上，对水沙条件发生较在变化时的平衡纵比降以及带来的对长江中下游防洪的影响进行了分析。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

一种蒸发式冷凝器的新型设计方法

蒸发式冷凝器设计方法的粗糙和繁琐限制其广泛应用,特别是限制其应用于民用和小型商用建筑中。针对上述问题,作者通过实验研究了蒸发式冷凝器的影响因素（进风湿球温度、最小截面风速和喷淋水量）对蒸发式冷凝器热质交换的影响。同时提出了一种新型设计方法,此方法简单,精度较高。适合工程设计、选型和生产应用。