银铜复合电触点复合强度检测方法的讨论

贵金属及其合金铆钉型复合电触点除了应考核其冷态复合强度之外，还必须增加在热态下复合强度的考核，只有这样才能满足用户在产际运行时对复合触点复合强度的要求。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

Volatile organo-halogen trace analysis in beverages by thin-layer headspace enrichment and electron-capture gas-chromatography

Applicability of thin-layer headspace (TLHS) procedure giving an aqueous concentrate and also classical purge and trap (PT) in off-line mode to isolate and enrich volatile organohalogen compounds in common beverages was tested. Both enrichment tech-niques were used in combination with gas chromatography – electron capture detection (GC-ECD). TLHS, combined with direct aqueous injection (DAI)-GC-ECD, proved applicable in the determination of volatile organohalogen compounds in all studied beverages, while the PT in a version with no preliminary sample pre-treatment was of limited applicability. Detection limits of the TLHS-based procedure were in the order of 1 ppt. Content of volatile organohalogen compounds in a number of beverages available on the Polish market including mineral waters, beers, juices, carbonated and non-carbonated soft drinks, etc. was determined by means of TLHS-DAI-GC-ECD.     

天津钢管公司DRC直接还原厂生产工艺与自动控制

天津钢管公司DRC直接还原厂将采用英国戴维国际工程公司的DRC煤基直接还原技术,以铁矿石、煤、石灰石为原燃料,用回转窑来生产直接还原铁(DRI)。该厂将由两条回转窑生产线组成,每条生产线的生产能力为15万tDRI/年,回转窑规格为φ5.0m×80m。工厂生产主线将采用计算机集散控制系统(DCS)以实现对生产过程的自动控制。     

Reduction of Stibnite at Moderate Temperature

Reduction of stibnite with hydrogen in the presence of calcium oxide has been experimentally inves-tigated at moderate temperature. The results reveal that the effluent generated in the reduction pro-cess contains much less air-polluting substance H_2S, and that the reaction activation energy is63. 3 kJ/mol. The form of antimony changes considerably when the reaction temperature varies.     

The performance of a direct-sequence spread-spectrum acquisition system using a linear prediction filter for narrowband interference suppression

The coarse acquisition performance of a direct sequence spread-spectrum receiver is analyzed when a linear prediction filter is used for narrowband interference suppression. We show that once an appropriate matching strategy is identified, the linear prediction filter can provide favorable performance when narrowband interference is present over a considerable range of both interference power and bandwidth. In addition, the presence of the filter dramatically improves the performance over the case where there is no filter, except when the interference bandwidth and the power are both small (i.e., when the processing gain provides sufficient interference immunity without the filter). If long spreading sequences are used with moderately sized observation windows, the acquisition performance can be severely degraded when a parallel acquisition scheme is used due to the linear predication filter. We show, however, that a slower serial receiver will provide reliable performance.This work was supported in part by the Office of Naval Research under contract ONR N00014-91-J-1234, the Army Research Office under contract ARO DAAL03-91-0071, and the NSF Center for Ultra-High Speed Circuits and Systems (ICAS).     

The effect of pre-wetting on dynamic contact angles

A roll-coating experimental system is used to study the effect of pre-wetting on dynamic contact angles, the interfacial displacement depth, and the associated phenomenon of air entrainment. The system consists of a roll, which is horizontally rotating in a liquid pool. The dynamic contact angle is recorded by a macrophotography system. The test liquids are glycerol solutions with viscosities in the range 104 < μ < 748 mPa · s. The value of (μV/ρg)^0.5 is taken as the characteristic length to be used in the dimensionless relationships which correlate experimental measurements. The effect of base layer entry angle into the liquid pool on the dynamic contact angles and other flow parameters is studied. Comparison is made with measurements in dry tape-coating and other pre-wet roll–coating systems.     

直流励磁机电刷打火的常见原因及对策

主要介绍了中铝公司山西分公司自备热电厂6台发电机组的励磁机电刷打火的常见原因的分析和处理方法。     

接触传热表面粗糙度曲线的统计特征

测量了一般机械加工表面的轮廓曲线，基于小波变换提取了粗糙度曲线，分析了轮廓高度和接触峰高度的统计分布特征。研究结果表明，轮廓高度不服从严格的正态分布，但具有一定的正态性，而接触峰高度的统计特征与其评定标准有直接的关系。因此，对于接触热阻的计算模型来说，接触点数的计算应以合理选取接触峰的评定标准为前提。