A method to estimate entropies and heat capacities applied to alkali oxides

We present a method that is useful in the estimate and assessment of heat capacity data. The approach is based on an analysis of the logarithmic average of the phonon frequencies. In this quantity, that may be easily derived from experimental data on the vibrational entropy, the influence of atomic masses can be exactly accounted for even in polyatomic solids. Our method is applied to Li₂O, Na₂O, K₂O, Rb₂O, and Cs₂O. In particular, literature data for K₂O are critically examined.     

Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

复合脱氧剂对纯净钢生产的影响

论述复合脱氧剂的一般化学特性，并以碳化硅和硅铝铁两种复合脱氧剂为例，讨论其对改善钢的质量，进行纯净钢生产的影响。     

Photo-reversible Reaction in Polymer Langmuir-Blodgett Films

Preparation of photoreactive Langmuir-Blodgett (LB) films was carried out using polymers/oligomers prepared from long-chain dialkyl esters of di-and tetra-olefins and having cyclobutane rings in the main chain. These polymers/oligomers formed stable monolayers on a water surface when mixed with arachidic acid. These monolayers could be deposited onto a substrate successfully forming Y-type films. The oligomer LB films were polymerized on irradiation. The polymer LB films showed a photo-reversible process between polymers and oligomers, depending on wavelength of the irradiating light. On the basis of spectral data and molecular weight change, this behaviour was found to be caused by cleavage and formation of cyclobutane rings.     

The design of experiments when there are errors in all the variables

The Error-in-Variables Model (EVM) applies to a large class of problems in parameter estimation in which there is error in all the variables. This property makes it of more general applicability than the widely used technique of ordinary Least Squares. While there is a voluminous literature on EVM there is nothing on a general method for designing experiments when EVM applies. In this paper we present an extension of the concept of D-optimality to provide such a general method. It is illustrated by applying it to the estimation of copolymer reactivity ratios and to fitting an ellipse.     

门式脚手架在已建高层建筑外装修中的应用

介绍门式脚手架在已建高层建筑外排栅中的整体搭设和应用实例。     

Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.