The Simulation of Impact Loads on Beam-type Structures using a Pseudo-dynamic Procedure

Abstract:  This study proposes an alternate method for the analysis of beams with solid cross-section or built as a framed structure and subjected to transverse impact loads from an external striker. The procedure used in the analysis is a combination of two essential tools using pseudo-dynamic techniques. The method reported here involves only one degree of freedom for the structure modelling and assumes an elastic contact between an external striker and the beam structure, which in reality does not happen. As only one degree of freedom is considered in the analysis, some important limitations are inherent to the method proposed here. Essentially, there is the difficulty of modelling the displacement field associated with the transient structure behaviour accurately, as a consequence of fast-rate impact loads. Another difficulty faced by the method refers to a local structure behaviour associated with contact loads. The present method can deal with large displacements in transversely loaded beams associated to a collapse mechanism having a simple geometry and defined with precision from a single parameter. This ensures reasonable accuracy in the evaluation of the strain energy absorbing capacity of transversely impacted beam structures using a single degree of freedom model in a pseudo-dynamic procedure.     

Density Measurement of Liquid Ni-Ta Alloys by a Modified Sessile Drop Method

The density of liquid Ni- Ta alloys was measured by using a modified sessile drop method. It is found that the density of the liquid Ni- Ta alloys decreases with the increasing temperature, but increases with the increase of tantalum concentration in the alloys. The molar volume of liquid Ni- Ta binary alloys increases with the increase of temperature ancl tantalum concentration.     

矿石中金的快速测定

研究了活性炭纤维滤布富集分离的条件和解脱方法,并利用微波溶样、液珠萃取比色法测定矿石中的金。该方法的测定范围为(0.5~xx)×10-6,相对标准偏差RSD为3.2%,可用于矿石中金的野外快速测定。     

Measurement and prediction of pressure drop in two-phase flow

Experimental data for air–water two-phase co-current flow in two different pipe diameters were used to test the prediction of pressure drop by a number of existing theories and correlations. Several models are shown to be useful for prediction, particularly with the stratified regimes which have proved difficult to handle in the past. The model suggested by Olujic proved to be of particular value.     

单小区模型的掉话率分析

掉话率是无线通信网络中最重要的关键性能指标(KPI)之一,本文分析了中国移动在讨论网络性能评估方法时提出的3个不同的掉话率计算公式,通过建立一个单小区的模型,使用一些合理的假设和分析,从理论上确定了一个最为准确的计算公式.     

川中地区上三叠统天然气地球化学特征及成藏过程探讨

川中地区上三叠统是一套自生自储的天然气成藏系统，天然气中甲烷含量为88%～96％，重烃（C2＋）含量一般在6％～9％之间，二氧化碳和硫化氢等非烃气体含量普遍较低；天然气干燥系数（C1／C2＋）为5～15，并且随深度增加而呈现升高的趋势；天然气和凝析油轻烃中的甲基环己烷、庚烷和异庚烷值变化表明天然气主要来源于腐殖型母质；天然气甲烷和乙烷碳同位素分别为-39．00‰～-41．00‰和-25．00‰～-27．00‰，具有典型煤成气特征。川中地区上三叠统烃源岩在燕山期持续沉降埋藏过程中，达到高成熟早期阶段；在喜山期，该地区大约2500m地层的剥蚀，使地层温度和压力大幅度降低，故储层中早期低成熟残余天然气的卸压膨胀作用和水溶气的脱溶作用为晚期天然气聚集成藏提供了重要的气源，同时也使气藏中甲烷碳同位素变轻。     

阳极炭块压降测试的方法与分析

本文通过阐述新的阳极炭块测试方法，提出了降低阳极炭块Fe-C压降的思路，并分析了降低阳极炭块压降对我公司经济效益的影响，可供同行参考。     

A motivational model of rural students' intentions to persist in, versus drop out of, high school.

Using self-determination theory, the authors tested a motivational model to explain the conditions under which rural students formulate their intentions to persist in, versus drop out of, high school. The model argues that motivational variables underlie students' intentions to drop out and that students' motivation can be either supported in the classroom by autonomy-supportive teachers or frustrated by controlling teachers. LISREL analyses of questionnaire data from 483 rural high school students showed that the provision of autonomy support within classrooms predicted students' self-determined motivation and perceived competence. These motivational resources, in turn, predicted students' intentions to persist, versus drop out, and they did so even after controlling for the effect of achievement. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

基于高抗热震性能的陶瓷刀具材料的微观结构设计

本文以现有的抗热震断裂和抗热震损伤的评价理论为基础，通过对材料中微裂纹的长度进行预测，从而实现了对陶瓷刀具材料的抗热震性能的微观结构设计。根据此理论对现有材料的抗热震性能的进行预测，预测结果与实际的测量结果相符，验证了该理论的正确性。     

光学薄膜在光通信中的应用

主要介绍了光学薄膜在光通信的无源型器件中的原理及应用,并与光纤光栅和平面光波导型的无源器件作简单比较。