Preparation of Plate Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) Bulk Amorphous Alloy and Its Fracture Toughness

1Introduction Duwez[1]synthesizedthefoilAu Siamorphousalloyforthefirsttimewithrapidsolidification,whichinitiatedthepreparationofamorphousalloysintheprocessofalloysolidification,andthereaftertheresearchonamorphousal loysdevelopedrapidly.Since1980s,withthec…     

Fracture toughness of thermoset composites reinforced by perfectly bonded impenetrable short fibers

The fracture toughness of brittle thermoset resins could be improved significantly by perfectly bonded tough, short fibers through both crack trapping and bridging effects. In this paper, the crack trapping effect was studied through the analysis of the change of strain energy associated with the crack propagation across a regular array of fibers, and the bridging effect was discussed based on the Andersson–Bergkvist model. The fracture resistance increases with the fiber volume fraction, and is independent of the elastic properties of the matrix, the crack length, and the cross-sectional diameter of the fibers.     

Fracture Resistance of Ceramics upon Edge Chipping

Modern methods of determining fracture resistance are analyzed. The necessity of developing a crucially new method based on edge chipping of a brittle material is shown. The results of experimental studies are presented. The applicability of the method to the comparative fracture resistance evaluation of ceramics is substantiated.     

Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

铈和磷对中碳锰钢低温回火脆性的影响

本文采用冲击试验和断口扫描电镜，俄歇谱分析等方法，研究了铈对不同磷含量的中碳锰钢低温回火脆性的影响。结果表明，磷在奥氏体晶界偏聚是导致含磷锰钢产生低温回火脆性的原因，而铈的加入，可减少磷的偏聚程度，增加回火马氏体的冲击值，从而降低中碳锰钢的回火脆性。     

图象中心加权中值滤波的改进与应用

中心加权中值滤波具有较好的边缘保持特性及快速实现的特点，但滤噪能力低于其它中值滤波。此文探 讨对中心加权中值滤波的改进方法，提出了中心加权分级实现的思想，使之同时具有边缘保持、快速滤波和噪声去 除的理想效果。     

眼球的自动定位

提出了一种由粗到细自动定位人脸的一个重要特征即眼球圆心的方法，该方法综合运用局部二值化，霍夫变换，像纱聚类，边缘提取等技术，对均匀或非均匀光照下拍摄或戴眼镜的照片都能获得很高的定位精度，适用于处理证件照。     

Edge detection,three-dimensional cell boundary reconstruction and volume and surface area estimation from differential interference contrast images

Three-dimensional (3-D) cell morphology is important for the understanding of cell function and can by quantified in terms of volume and surface area. Differential interference contrast (DIC, or Nomarski) imaging can enable cell edges to be clearly visualized in unstained tissue due to the slight difference in refractive index between aqueous media and cytoplasm. DIC is affected in only one direction - the direction of the optical shear. A 1-D edge detector was used in that direction with a scale length equal to that of an in-focus edge to highlight cell boundaries. By comparison with the signal from the edge detector on an out-of-focus slice, the in-focus slices could be segmented and, after noise suppression, cell outlines obtained. A voxel paradigm was used to calculate cell volume and differential geometry was used for surface area estimation. We applied this approach to obtain 3-D dimensional information by optical sectioning of motile Amoeba proteus.