复合乳化沥青的粘附性试验方法研究

鉴于目前使用的阳离子乳化沥青粘附性试验方法难以有效评价复合乳化沥青粘附性，通过试验研究并综合考虑乳化沥青施工和路用实际情况，提出了乳化沥青水煮法试验方法和采用该方法检验复合乳化沥青粘附性时的评定标准。     

新型高温高密度W/O乳化钻井液的研制

研制了油包水乳化钻井液的基本配方，评价了其抑制性，热稳定性，以及抗水侵污能力，抗钻屑侵污能力，抗水泥侵污能力。现场应用表明，该体系具有较强的抑制作用，能很好地稳定井壁，保护油气层。     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

乳化型轧制液的质量标准研究

对国内目前所使用的冷轧薄钢板(汽车钢板)轧制液母液和乳化液的质量指标及常用试验评定方法进行了考察，并对产品的性能要求进行了研究与分析，制订出一套标准以供参考，包括乳化液稳定性、润滑性、防锈性、抗泡性、使用周期及粘度、闪点等性能。     

失水山梨醇倍半油酸酯的合成

考察了合成乳化剂失水山梨醇倍半油酸酯（ＡｒｌａｃｅｌＣ）的原料配比、反应温度、反应时间、催化剂用量对产品性能的影响，并找到了最佳反应条件．     

纳米聚N-异丙基丙烯酰胺微凝胶的光引发聚合

选择具有温敏性的高分子单体N－异丙基丙烯酰胺（N－isopropylacrylamide，NIPAM）为主单体，N，N′－亚甲基双丙烯酰胺（methylenebisacrylamide，MBA）为交联剂，运用光引发无皂乳液聚合的方法合成出粒径小于100nm的高分子微凝胶，并研究了在改变体系组成和条件时微凝胶粒径的变化。结果显示，在乳化剂临界胶束浓度以下，随着乳化剂浓度的提高，微凝胶粒子的粒径不断关小且趋向稳定；相比于热引发，产生的微凝胶具有较高的单分散性而且粒径较小。     

Separation of di- and tripeptides with solvent extraction and an emulsion liquid membrane

The extraction equilibria of various di- and tripeptides with di-2-ethylhexylphosphoric acid (D2EHPA) were studied at low pH values. The complex extracted to organic phase consisted of one molecule of peptide and two molecules of D2EHPA dimer. The extraction constants of the peptides correlated well with the distribution coefficients of peptides between 1-octanol and water, which is a measure of hydrophobicity. The permeation rates of peptides through an emulsion liquid membrane were examined by using D2EHPA as a carrier, Span 80 as an emulsifier and kerosene as a diluent. The rates varied considerably with peptide type, depending upon the hydrophobicity.     

坨五站中间乳化层快速增长原因及治理方案

胜利采油厂坨五站高含水(95％)原油化学预脱水中，二级沉降罐内油水相之间的中间乳化层增长迅速，引起了一系列问题。现场调查和大量室内测试结果表明，产生这一现象的原因有：油溶性破乳剂WD-1加入点不合理。有2／3的含水原油在通过油水分离器之后才与破乳剂混合；二级沉降罐进油口伸入油相内，油流的冲击达不到中间层；WD-1对坨五站混合原油中的稠油破乳脱水性能欠佳，不能适应坨五站混合原油组成和含水的变化。针对上述各种原因筛选出了性能更好的一种破乳剂1916。根据确定的几种原因采取了相应的措施：将破乳剂加入点改在3个并联油水分离器之前；将二级沉降罐的进油口移到水相内；改用筛选出的破乳剂1916，结果使中间乳化层的增长受到了抑制。图2表4参2。     

聚氨酯-聚丙烯酸酯共聚乳液的成膜和性能

通过XPS和接触角测试研究了聚氨酯-聚丙烯酸酯共聚乳液在不同基材上的成膜情况，并对共聚胶膜的耐水性和附着力进行了考察．由于该共聚乳液同时存在着亲水组分和疏水组分，所以它在不同的基材上成膜可导致其膜表面的组成成分不同，因而导致其耐水性和附着力也随基材而异。结果表明，亲水性的聚氨酯组分均富集于胶膜内部，但胶膜底层聚氨酯组分的含量却随基材的不同而不同。在憎水且表面张力较高的基材上，共聚胶膜的耐水性良好；共聚胶膜的附着力在表面张力较高的基材上也良好。     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry