Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.     

The Minimum PAPR Code for OFDM Systems

In this letter, a block code that minimizes the peak‐to‐average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals is proposed. It is shown that peak envelope power is invariant to cyclic shift and codeword inversion. The systematic encoding rule for the proposed code is composed of searching for a seed codeword, shifting the register elements, and determining codeword inversion. This eliminates the look‐up table for one‐to‐one correspondence between the source and the coded data. Computer simulation confirms that OFDM systems with the proposed code always have the minimum PAPR.     

抓紧有利时机 搞好更新换代

本文简要回顾了１５０发动机发展历史，阐述了世界坦克动力发展现状，列举了几种对１５０ 继续发展的看法，认为从综合约束条件和高紧凑性考虑，仍以保持或适当减少缸径较优．指出当 前是追赶世界先进水平的极好时机，要牢牢把握住这个稍纵即逝的机遇．     

变结构变参数设计方法及其在机械CAD中的应用

提出了一种新颖的机械结构设计思想－变结构变参数设计方法，并结合实例，阐述了变结构变参数设计的概念、原则、实施措施和意义。由此对Ｉ－ｄｅａｓ软件包进行了二次开发，编制了发动机曲轴专用ＣＡＤ软件程序，并用某型号发动机曲轴进行了验证。     

稳定同位素井间示踪技术在深层块状稠油油藏水驱特征研究的应用

经对冷43块深层块状普通稠油水驱注水5个试验井组开展的稳定同位素示踪测试，利用中子活化技术分析样品，采用先进的示踪剂定量分析与流动模拟相互结合的方法，以示踪数值模拟为手段，评价了油井连通、油层平面及纵向上的非均质性、隔层的封隔性等因素对水驱控制程度及动用状况的影响，通过优化注水推进方向及速度，强化动态调整措施，提高了稳产基础。     

苯乙烯类嵌段共聚物的生产及市场分析

介绍了苯乙烯类嵌段共聚物(SBC)的国内外生产和消费情况，分析了我国SBC的市场前景，提出了加大研发力度、提高SBC生产术、扩大生产规模、提高国内市场占有率，建设多功能装置等建议。     

未来航空润滑油基础油

介绍了未来航空涡轮发动机对润滑油性能的要求:在260,-54℃时,试样运动黏度分别大于1.0 mm2/s和小于15 000 mm2/s,热氧化安定性温度为260~427℃。该要求已超出了目前使用的酯类润滑油所能承受的最大极限。为了满足要求,需开发全氟聚醚、改性硅油、聚苯醚、C-型醚、氟醚三嗪及环三磷偶氮润滑油基础油,它们的使用温度依次为:-34~316,-60~260,5~288,-29~260,-30~343,-15~343℃。     

线性分组码的神经网络译码

介绍了神经网络与线性分组码之间的关系，并在文献[1]的基础上证明了软判决译码与求解能量函数最大值之间的等价性，然后以(7，4，3)汉明码为例介绍了神经网络在循环码硬判决、软判决译码中的应用。     

基于LabWindows/CVI的某型飞机FBW飞行试验台设计与实现

主要阐述了某型飞机EBW飞行试验台的LabWindows／CVI实现。在分析EBW组成及信号交联关系的基础上，设计了PCI总线结构的系统硬件；提出了测试库与测试引擎相结合的编程方法，并着重阐述了测试引擎的实现方法。     

汽车发动机电机铁芯用钢(ADW2)的研制开发

鞍钢研制开发的汽车发动机启动电机用钢是针对汽车电机铁芯用钢（定、转子）而开发的电机钢类产品。介绍了该产品的研制过程及规格、特点。通过批量试制及装机试验，产品巳满足用户的使用要求。