炭黑对轮胎胎面胶热物性的影响

研究了炭黑品种和用量对轮胎胎面胶热扩散系数(α)、导热系数(λ)及比热容(C)3种热物性参数的影响规律。结果表明,随着炭黑填充量的增加,胎面胶的α及λ均逐渐增大,C逐渐减小。炭黑的结构性对胎面胶α的影响程度大于炭黑的粒径;温度相同时,炭黑的结构性越高,其填充胎面胶的α越大;随着炭黑填充量的增加,3种炭黑填充胎面胶α之间的差距呈现先增大后减小的变化趋势。炭黑的结构性及粒径对胎面胶C的影响没有固定的规律,但在低温区,炭黑的粒径越大,其填充胎面胶的C越大,且炭黑填充量对此差距无影响。炭黑的结构性对胎面胶λ的影响程度大于炭黑的粒径;温度相同时,炭黑的结构性越高,其填充胎面胶的λ越大;当炭黑用量较低时,其对胎面胶λ的影响程度相对较小,随着炭黑填充量的增加,3种炭黑填充胎面胶λ之间的差距呈现先增大后减小的变化趋势。     

炭黑填充硬聚氯乙烯的改性

为使聚氯乙烯具有抗静电性能,采用加入具有导电性填料的方法,但加入大量的填料,会使硬聚氯乙烯的冲击性能降低,加工性能变差。本文是在以炭黑为填料的基础上,研究不同的改性剂和加工助剂改进硬聚氯乙烯的效果,结果表明,加入冲击改性剂和加工助剂后,大大增加了硬聚氯乙烯的冲击强度,且加工性能也得到改善,同时由于炭黑具有补强效果,其拉伸强度和弯曲强度在加入改性剂后也能满足使用要求。     

碳黑水分离技术的研究

脱油沥青作为谢尔气化工艺的气化原料生产化肥在国内尚属首次,由于沥青原料中的灰分和重金属比渣油原料大得多,若仍采用石脑油萃取碳黑技术,灰分和重金属随碳黑返回气化装置,将造成设备的堵塞、磨损,无法保证设备安稳长期运行.通过对碳黑水分离技术进行多方面的研究,寻找到适宜的工艺路线与解决方案.     

Effect of adhesive‐coated glass fiber in natural rubber (NR), acrylonitrile rubber (NBR), and ethylene–propylene–diene rubber (EPDM) formulations. II. Effect of cyclic loading,abrasion, and accelerated aging

Treated glass fibers (RICS, 3 and 6 mm in length) were added at a concentrations of 10, 20, and 30 phr in natural rubber (NR), nitrile rubber (NBR), and ethylene–propylene–diene comonomer (EPDM) formulations, in both plain and carbon black mixes. The compounds were mixed in two‐roll mill and were evaluated for their resistance to hot‐air aging, abrasion, compression set, Goodrich heat buildup, De Mattia fatigue, and for NR mixes, adhesion in the tensile mode. The vulcanizates of the three rubbers showed resistance to hot‐air aging. Abrasion resistance was poor for NR, and it improved with carbon black addition in the presence of treated glass fiber in NBR. In carbon‐black‐added EPDM vulcanizates, the abrasion resistance and fatigue resistance were better. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1124–1135, 2004     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

P(SBR/NR/HAF)并用胶的性能

在SBR胶乳／NR胶乳共混的基础上，采用凝聚共沉法制备高耐磨炭黑（HAF）填充型粉末丁苯橡胶／天然橡胶并用胶[P(SBR/NR/HAF)]。研究了SBR／NR并用比、制备工艺等对P（SBR／NR／HAF）并用胶的混沌流变性能和物理机械性能的影响，并与块状SBR／NR／HAF并用胶进行了比较。研究表明，与SBR／NR／HAF相比，P（SBR／NR／HAF）的表观剪切粘度在SBR用量小于50份时对混炼时间的依赖性较低，而在SBR用量大于50份后对混炼时间具有更高的依赖性；P（SBR／NR／HAF)硫化胶 拉伸强度在整个并用范围内对SBR／NR并和比不敏感；采用胶乳预混合的工艺制备的P（SBR／NR／HAF）具有较好的物理机械性能。     

炭黑对复合型导电高分子材料电性能影响

阐述了炭黑填充型导电高分子复合材料的导电机理，讨论了炭黑基本物性、填充量以及分散状态对材料导电性的影响，并探讨了影响炭黑分散状态的因素。     

竹材丙酮法木质素高效分离技术研究

在一定的温度、压力条件下,利用丙酮提取竹材中的木质素,丙酮通过蒸馏回收后,可以反复利用;而通过蒸馏,得到的高纯度的木质素是重要的化工原料,整个过程形成一个封闭循环系统,基本上无三废排放;研究结果表明:当丙酮浓度为80%,液固比为10∶1,在最高反应温度160℃下保温3h,降解木质素的效果最佳;为解决制浆造纸行业废水对环境的污染问题提出了一条新的途径。     

由沥青制备多孔炭的工艺研究

采用沥青加发泡剂加炭黑制备了孔结构较好的多孔炭材料，分析和讨论了该工艺中沥青、发泡剂及炭黑的作用和影响，对多孔炭材料进行了力学性能测试和微观电镜观察分析，探讨了其可能的应用前景。     

感光材料内包装黑色膜的制造工艺与性能

感光材料包装膜分为内包装膜和外包装膜。本文主要介绍内包装用黑色膜的技术现状,制造工艺,包括原材料的选择,工艺技术路线及关键设备,并列举了产品主要规格与性能指标以及加工应用。