高压水射流射孔井眼应力数值模拟研究

水力射孔技术是一种新型完井方式,利用深穿透水力射孔技术辅助定向压裂,可实现油层改造和油井增产。考虑套管水泥环的影响,采用有限元理论结合ANSYS软件计算了高压水射流水力射孔井眼周围的应力,重点分析了水力射孔参数对井周应力的影响规律,初步研究了直井水力压裂时水力射孔对裂缝起裂的影响。计算结果表明,沿最大水平地应力方向布孔时,孔眼根部的周向拉应力最大,裂缝将会在孔眼根部起裂;选择合理水力射孔参数可有效降低地层破裂压力。研究结果可为高压水射流水力射孔辅助定向压裂提供参数优选的依据。     

Fracture Resistance of Ceramics upon Edge Chipping

Modern methods of determining fracture resistance are analyzed. The necessity of developing a crucially new method based on edge chipping of a brittle material is shown. The results of experimental studies are presented. The applicability of the method to the comparative fracture resistance evaluation of ceramics is substantiated.     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

Characterization of strength properties of thin polycrystalline silicon films for MEMS applications

The aim of this work is to characterize the strength properties of polycrystalline silicon (polysilicon) with the use of tensile and bending test specimens. The strength of thin polysilicon films with different geometry, size and stress concentrations has been measured and correlated with the effective size of the specimen and its stress distribution. The test results are evaluated using a probabilistic strength approach based on the weakest link theory with the use of STAU software. The use of statistic methods of strength prediction of polysilicon test structures with a complex geometry and loading based on test values for standard material tests specimen has been evaluated.     

Low-cycle fatigue properties of eutectic solders at high temperatures

This paper details the deformation mechanism and low‐cycle fatigue life of eutectic solder alloys at high temperature (around 0.8T_m). Grain boundary sliding generally nucleates a wedge‐type cavity that reduces the low‐cycle fatigue life of metals. In this study, grain boundary sliding has promoted intergranular failure contributing to the reduction in fatigue life of Sn–Ag–Cu alloy. However, grain boundary sliding has exerted no deleterious effects on fatigue resistance of eutectic Pb–Sn and Bi–Sn alloys. The phase boundary sliding with very fine microstructure induces exceptional ductility in these alloys leading to superior low‐cycle fatigue endurance for theses eutectic Pb–Sn and Bi–Sn alloys.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

Crack closure in fibre metal laminates

GLARE is a fibre metal laminate (FML) built up of alternating layers of S2-glass/FM94 prepreg and aluminium 2024-T3. The excellent fatigue behaviour of GLARE can be described with a recently published analytical prediction model. This model is based on linear elastic fracture mechanics and the assumption that a similar stress state in the aluminium layers of GLARE and monolithic aluminium result in the same crack growth behaviour. It therefore describes the crack growth with an effective stress intensity factor (SIF) range at the crack tip in the aluminium layers, including the effect of internal residual stress as result of curing and the stiffness differences between the individual layers. In that model, an empirical relation is used to calculate the effective SIF range, which had been determined without sufficiently investigating the effect of crack closure. This paper presents the research performed on crack closure in GLARE. It is assumed that crack closure in FMLs is determined by the actual stress cycles in the metal layers and that it can be described with the available relations for monolithic aluminium published in the literature. Fatigue crack growth experiments have been performed on GLARE specimens in which crack growth rates and crack opening stresses have been recorded. The prediction model incorporating the crack closure relation for aluminium 2024-T3 obtained from the literature has been validated with the test results. It is concluded that crack growth in GLARE can be correlated with the effective SIF range at the crack tip in the aluminium layers, if it is determined with the crack closure relation for aluminium 2024-T3 based on actual stresses in the aluminium layers.     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.     

Finite-element analysis and experimental study on tensile fatigue behaviour of bitumen–stone adhesion

Tensile fatigue behaviours of bitumen–stone adhesion were investigated using a dynamic mechanics analyser under stress‐controlled mode at two temperatures of 5 and 25°C and various controlled‐stress levels. Failure characteristics including interfacial failure and cohesive failure were examined using image analysis of fracture surfaces. Finite‐element analysis on stress distributions was conducted under different temperatures, film thickness and interfacial bonding conditions. A Coulomb–Mohr like criterion in combination with shear and normal stresses is proposed to deal with the extreme thin adhesive layer, which can be further simplified into an adhesive zone without significant loss of accuracy for stress analysis.     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。