丹尼尔流动点在涂料配方设计中的应用

对于给定的树脂、颜填料体系,采用丹尼尔流动点理论对分散剂进行定性选择和用量试验,并将设计配方推广至生产应用。     

Editorial: Biodegradable Materials

This Special Issue “Biodegradable Materials” features research and review papers concerning recent advances on the development, synthesis, testing and characterisation of biomaterials. These biomaterials, derived from natural and renewable sources, offer a potential alternative to existing non-biodegradable materials with application to the food and biomedical industries amongst many others. In this Special Issue, the work is expanded to include the combined use of fillers that can enhance the properties of biomaterials prepared as films. The future application of these biomaterials could have an impact not only at the economic level, but also for the improvement of the environment.     

High dielectric permittivity and percolative behavior of polyvinyl alcohol/potassium dihydrogen phosphate composites

A new kind of anhydrous, transparent, and flexible potassium dihydrogen phosphate (KH₂PO₄ or KDP)/polyvinyl alcohol (PVA) composite in the form of film (0.10 mm) has been prepared by solution casting technique. KDP is well dispersed in the polymer matrix as observed from the microstructural studies. Frequency and temperature dependent dielectric properties of the composites have been studied with varying KDP concentrations. The PVA/KDP composite films exhibited extraordinarily high relative permittivity ε′ ∼ 430 (80 times higher compared with pure PVA and even higher than KDP) near the percolation threshold (ϕ_C = 2.5 wt % KDP) with low dielectric losses (∼ 0.15) at 1 kHz and room temperature. Such flexible, low loss and high dielectric permittivity material has enormous importance for application in devices. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Utilization of linseed cake as a postagricultural functional filler for poly(lactic acid) green composites

Linseed cake (LC), a byproduct of linseed oil extraction, is used as a functional filler for production of biodegradable composites. To determine the influence of residual linseed crude oil contained in lignocellulosic filler on the properties of the poly(lactic acid) (PLA)-based composites with 5–30% filler content, two types of LC were analyzed: a defatted and an unmodified one. Complex analysis of the composites' properties change was conducted in relation to their structure modification caused by the addition of a waste filler. It was found that the addition of LC resulted in simultaneous plasticization and improved crystallization of PLA. Lignocellulosic particles and crude linseed oil contained in the LC powder provided a modifying effect, influencing the level of crystallinity and mechanical and thermomechanical properties. Using LC may thus overcome one of the main drawbacks of PLA, which is brittleness and low crystallinity. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47152.     

单组份聚氨酯炮孔填塞剂应用性试验

炮孔填塞是爆破施工过程中的一个关键环节,也是践行精细爆破设计理论的重要措施。传统的炮泥填塞存在着诸多不足,为此,研制了以聚氨酯为基材的TK炮孔填塞剂,通过大量基础性能研究和隧道现场工业性试验,论证了其作为炮孔填塞材料可降低炸药单耗,提高单循环进尺和炮孔利用率,减小空气冲击波、爆破噪声等有害效应的影响,且是安全可靠的。TK炮孔填塞剂优良的填塞效果、方便快捷的施工方法及显著的经济效益,方便于在爆破工程中推广应用。     

Tribological properties of ethylene–propylene–diene rubber + polypropylene + thermal‐shock‐resistant ceramic composites

This work is part of a program on composites used in thermoelectric devices. Tribological properties of dynamic vulcanizate blends of polypropylene and ethylene‐propylene‐diene rubber filled with 5 wt% of microscale powder have been studied. The microscale thermal‐shock‐resistant ceramic filler contains α‐Al₂O₃, mullite (3Al₂O₃ · 2SiO₂ or 2Al₂O₃SiO₂), β‐spodumene glass‐ceramic and aluminium titanate. We found that our ceramic particles are abrasive; they cause strong abrasion of softer steel ball surfaces during dry sliding friction. To overcome the difficulty of particle dispersion and adhesion, the filler was modified through grafting using three types of organic molecules. Dry sliding friction was measured using four types of counter‐surfaces: tungsten carbide, Si₃N₂, 302 steel and 440 steel. Thermoplastic vulcanizate filled with neat ceramic powder shows the lowest friction compared to composites containing the same but surface‐treated powder. We introduce a ‘bump’ model to explain the tribological responses of our composites. ‘Naked’ or untreated ceramic particles protrude from the polymer surface and cause a decrease of the contact area compared to neat polymer. The ball partner surface has only a small contact area with the bumps. As contact surface area decreases, so does friction and the amount of heat generated during sliding friction testing. Chemical coupling of the ceramic to the matrix smoothens the bumps and increases the contact surface, giving a parallel increase in friction. Copyright © 2012 Society of Chemical Industry     

LPM填充体混凝土空心楼盖施工技术

清华大学综合科研楼采用LPM填充体空心楼盖。介绍该楼盖的构造、施工流程和轻质管抗浮等技术措施。为保证楼盖质量,应重视组合模件的安装铺设和各专业工种的沟通配合。     

Curing enhancement and network effects in multi‐walled carbon nanotube‐filled vulcanized natural rubber: evidence for solvent sensing

Electrically and thermally conductive polymer composites offer great possibilities in various electronic fields because of their low weight and ease of processing. This paper addresses the curing behaviour and network properties of conducting multi‐walled carbon nanotube (MWCNT)‐reinforced natural rubber (NR) nanocomposites, emphasizing the sensing and diffusion performances. NR/MWCNT composites were prepared following a special master batch technique which allows the appropriate distribution of nanotubes within the elastomer. The sensing responses of the composites towards solvents were observed as variations in electrical resistance. Thermal resistance and glass transition behaviour were examined and correlated with the swelling measurements as evidence for solvent sensing. An optimum level of 3 phr of MWCNTs is understood to lead to the best properties for the NR/MWCNT composites. Finally, the structural morphology and interfacial interactions were found to have correlations with cure reactions, glass transition temperatures and sensing responses of all compositions. © 2017 Society of Chemical Industry     

Microperforation of Three Common Plastic Films by Laser and Their Enhanced Oxygen Transmission for Fresh Produce Packaging

Three different plastic films of biaxially oriented polypropylene (BOPP), biaxially oriented polyethylene terephthalate (BOPET) and low‐density polyethylene (LDPE) were perforated using Nd‐YAG laser. Effects of laser pulse energy were examined by varying energies from 50 to 250 mJ where the pulse duration and pulse repetition were kept constant at 10 ns and 1 Hz, respectively. It was found that perforation diameters of all films increased with increasing pulse energies. Observed perforations were different among the three film types. Explanation was contributed to material inherent property and its interaction with laser. Incorporation of an inorganic filler (i.e. silica based anti‐blocking agent used in packaging film) of 0.5 wt% into the LDPE films (0.5Si‐LDPE) could improve perforation performance for LDPE. This was attributed to an increased thermal diffusivity of the 0.5Si‐LDPE film. Commercial BOPET and BOPP films containing 97 microholes/m² (hole diameter of ~100 µm) showed an improvement in oxygen transmission rates (OTR) of 18 and 5 times that of the neat films without perforation. In the case of perforated 0.5Si‐LDPE films having similar perforations of 97 microholes/m² and perforation diameter of 100 µm, a two‐fold increase of OTR was obtained. Gas transmission rates of the microperforated films were measured based on the static method. Measured OTR and CO₂TR values of the three films with varying perforation diameters in a range of ~40–300 µm were compared and discussed. Overall results clearly indicate that perforation by laser is an effective process in developing breathable films with tailored oxygen transmission property for fresh produce packaging. Copyright © 2014 John Wiley & Sons, Ltd.     

谈公路土方工程对填方料的要求与试验方法

论述了公路路基与底基层对填料的要求,结合实际试验数据,主要对填料的级配模数、线性收缩、击实度与CBR的试验方法进行了分析,通过试验结果分析,证明了该填料选择能够满足公路工程施工要求。