Development in graphite, graphene, and graphene nanoplatelet composites with epoxy matrix is presented here. Graphite and its modified forms propose exclusive properties to composites. Graphene has developed as subject of huge scientific attention due to excellent electron transport, mechanical properties, and high surface area. When combined appropriately with epoxy, these atomically thin carbon sheets can expressively progress physical properties even at very small loading. Epoxy/graphene nanoplatelet nanocomposite with enhanced properties was also reported. We summarized and compared electrical, thermal, and mechanical properties of epoxy composites derived from these three nanofillers. Potential of carbon fillers with epoxy matrix is also discussed. 相似文献
In many industries, there are applications that require the joining of stainless steel and copper components; therefore, the welding of dissimilar stainless steel/copper joints is a common process. For this investigation, the optimal brazing conditions and suitable filler metals for laser brazing of stainless steel/copper lap joints were studied. Tensile shear force increases with increases in the laser spot diameter or in the laser irradiation angle, which is associated with increased bonding width; however, as bonding width approaches 2 mm, tensile shear force reaches a saturated value due to fracturing at the HAZ of the Cu base plate. In order to obtain joints with high tensile shear strength, laser brazing was optimized by using Cu–Si-based filler metal under the following conditions: laser power, 4 kW; spot diameter, 3 mm; laser irradiation angle, 80°; irradiation position shift, 0.6 mm; brazing speed, 0.30 m/min; and filler metal feed speed, 0.30 min. Concerning filler metals, it was found that the Ni–Cu type showed relatively large tensile shear force even at high welding speeds in comparison with those of the Cu–Si, Cu, Cu–Ni, Ni–Cu and Ni types, respectively. 相似文献
Rubber materials filled with reinforcing fillers display nonlinear rheological behavior at small strain amplitudes below γ0 < 0.1. Nevertheless, rheological data are analyzed mostly in terms of linear parameters, such as shear moduli (G′, G″), which loose their physical meaning in the nonlinear regime. In this work styrene butadiene rubber filled with carbon black (CB) under large amplitude oscillatory shear (LAOS) is analyzed in terms of the nonlinear parameter I3/1. Three different CB grades are used and the filler load is varied between 0 and 70 phr. It is found that I3/1(φ) is most sensitive to changes of the total accessible filler surface area at low strain amplitudes (γ0 = 0.32). The addition of up to 70 phr CB leads to an increase of I3/1(φ) by a factor of more than ten. The influence of the measurement temperature on I3/1 is pronounced for CB levels above the percolation threshold.
The selective wetting behavior of silica in emulsion styrene butadiene rubber (ESBR)/solution styrene butadiene rubber (SSBR) blends is characterized by the wetting concept, which is further developed for filled blends based on miscible rubbers. It is found that not only the chemical rubber–filler affinity but also the topology of the filler surface significantly influences the selective filler wetting in rubber blends. The nanopore structure of the silica surface has been recognized as the main reason for the difference in the wetting behavior of the branched ESBR molecules and linear SSBR molecules. However, the effect of nanopore structure becomes more significant in the presence of silane. It is discussed that the adsorption of silane on silica surface constricts the nanopore to some extent that hinders effectively the space filling of the nanopores by the branched ESBR molecules but not by the linear SSBR molecules. As a result, in silanized ESBR/SSBR blends the dominant wetting of silica surface by the tightly bonded layer of SSBR molecules causes a low‐energy dissipation in the rubber–filler interphase. That imparts the low rolling resistance to the blends similar to that of a silica‐filled SSBR compound, while the ESBR‐rich matrix warrants the good tensile behavior, i.e., good abrasion and wear resistance of the blends.