MOS结构准静态测试中的异常C—V曲线

本文报导了MOS结构在准静态测试中的异常电容-电压曲线。讨论了它们产生的原因。     

Bandwidth allocation algorithms for weighted maximum rate constrained link sharing policy

This paper addresses the problem of bandwidth allocation under the weighted maximum rate constrained link sharing policy and proves a key theory in the condition of allocation termination. We propose several algorithms with various worst-case and average-case time complexities, and evaluate their computation elapse times.     

GaAs FET辐射退化研究

低噪声ＧａＡｓ ＦＥＴ和功率ＧａＡｓ ＦＥＴ经中子辐射都未发生致命性的通或断失效，直流偏置伏态下，其失效模式仅仅表现为源漏饱和电流ＩＤＳＳ的退化降低，据此提出了ＩＤＳＳ退化失效与快中子注量φｎ之间的解析关键式ｌｎｙ＝ａ＋ｂｌｎφ。     

金刚石光电导探测器研制及在软X光测量中的初步应用

介绍了我们自己设计制造的天然Ⅱａ型金刚石光导探测器的结构，原理，制造工艺，实验标定及其在ＩＣＦ实验中软Ｘ光测量中的应用等。     

A region-based selective optical flow back-projection for genuine motion vector estimation

Motion vector plays one significant feature in moving object segmentation. However, the motion vector in this application is required to represent the actual motion displacement, rather than regions of visually significant similarity. In this paper, region-based selective optical flow back-projection (RSOFB) which back-projects optical flows in a region to restore the region's motion vector from gradient-based optical flows, is proposed to obtain genuine motion displacement. The back-projection is performed based on minimizing the projection mean square errors of the motion vector on gradient directions. As optical flows of various magnitudes and directions provide various degrees of reliability in the genuine motion restoration, the optical flows to be used in the RSOFB are optimally selected based on their sensitivity to noises and their tendency in causing motion estimation errors. In this paper a deterministic solution is also derived for performing the minimization and obtaining the genuine motion magnitude and motion direction.     

The integral experiment on beryllium with D-T neutrons for verification of tritium breeding

A clean benchmark experiment on beryllium was performed with D-T neutrons at the FNS facility of the Japan Atomic Energy Agency. The main objective was to verify the integral data related to the tritium production on lithium isotopes. Tritium production rates, as well as activation reaction rates were measured inside the beryllium assembly that was shaped as a pseudo-cylindrical slab with an area-equivalent diameter of 628 mm and a thickness of 355 mm. Experimental results were analyzed with a three-dimensional Monte Carlo transport code MCNP-4C and FENDL/MC-2.0, JENDL-3.2/3.3 neutron transport libraries. Evaluation of reaction rates was based on the cross section data taken from the JENDL Dosimetry File and ENDF B-VI data libraries. Analysis shows that all calculation combinations (transport and activation cross section libraries) used for evaluation of reaction rates give data that is agreeable with measured values within 10%.     

Analysis of low load transients for the Vandellòs-II NPP: Application to operation and control support

The Technical University of Catalonia (UPC) has been jointly working with the Asociación Nuclear Ascó-Vandellòs (ANAV) for a number of years in order to establish, qualify and use best estimate (BE) models for the reactors under the control of ANAV. ANAV is the consortium that is responsible for operation of the Ascó and Vandellòs-II reactors. The reactors are Westinghouse-design three-loop PWRs with an approximate electrical power of 1000 MW. The existing integral plant models for each plant are currently used for many different purposes among which are support of plant operation and control. Quite a number of studies have been done in order to improve both safety and plant competitiveness. Most of these dynamic analyses were carried out in relation to transients starting at nominal full power or at least, very close to full power. This paper develops a specific use of the Vandellòs-II plant model for operation and control support at low power involving new ranges of system actuation parameters. It also examines scenarios that are somewhat different from those typically analysed. The study starts showing the results of an assessment case, which is a start-up test and provides some additional qualification, and subsequently attempts to establish calculations to support both an improvement in feed water controls and to set up operating recommendations for low-load manual operation of feed water turbo-pump. Both results hopefully, will produce an outcome, which leads to an improvement in safety and reduces reactor trip probability.     

lmbench: an extensible micro‐benchmark suite

lmbench is a powerful and extensible suite of micro‐benchmarks that measures a variety of important aspects of system performance. It has a powerful timing harness that manages most of the ‘housekeeping’ chores associated with benchmarking, making it easy to create new benchmarks that analyze systems or components of specific interest to the user. In many ways lmbench is a Swiss army knife for performance analysis. It includes an extensive suite of micro‐benchmarks that give powerful insights into system performance. For those aspects of system or application performance not covered by the suite, it is generally a simple task to create new benchmarks using the timing harness. lmbench is written in ANSI‐C and uses POSIX interfaces, so it is portable across a wide variety of systems and architectures. It also includes powerful new tools that measure performance under scalable loads to analyze SMP and clustered system performance. Copyright © 2005 John Wiley & Sons, Ltd.     

Engineering Model of a Nonisobaric Heavily Laden Gas‐Particle Jet

An axisymmetrical model of a rapid nonisobaric heavily laden gas‐particle jet is developed. The model is based on the general functions for both axial and radial pressure distributions, which were discovered by a numerical study of rapid gas‐particle jets by the CFD code. The model equations were solved analytically. The results obtained by the model developed are in good agreement with those computed by the CFD code for a wide range of flow parameters.     

Developing real-time knowledge-based systems with PERFECT

PERFECT (Programming EnviRonment For Expert systems Constrained in reasoning Time) is aimed at providing the necessary engineering support in real-time knowledge-based system development. PERFECT bridges the gap between the traditional analysis and design methodologies, and the implementation tools for these systems. It does so by providing the means to construct a knowledge model and to choose a suitable inference strategy. Subsequently the properties of the knowledge model and inference strategy may be analysed. For instance, it may be checked whether the knowledge model contains sufficient knowledge to diagnose a fault in an industrial process. Moreover, it may be checked whether the inference engine is able to provide an answer to a certain problem in time. If not, the analyser of PERFECT proposes an alternative structure of the knowledge model. When the constructed knowledge model and the chosen inference strategy show the required time efficiency, the compiler of PERFECT may translate them to an actual real-time knowledge based system in COGSYS. In addition, guidelines are provided with respect to the design of the human-machine interface. The resulting system is an instrument—a source of information that can be used by the human operator during problem-solving, rather than a prosthesis—a device that solves the entire problem by itself and presents the outcome to the human operator.