三峡工程泄洪坝段表孔溢流面拉模施工技术

三峡工程泄洪坝段表孔溢流面主要采用一期预留台阶、二期拉模一次成形的方法施工,体型复杂,拉模施工难度大,施工质量要求高,在生产性试验以及对试验结果进行分析的基础上,对混凝土性能、拉模设计、施工措施等方面进行了改进,形成了一套成熟的拉模施工技术。施工结果表明,施工质量达到了设计要求。     

Decomposition of Time Series Dynamic Linear Models

This paper derives the admissible decompositions for a time series dynamic linear model, assuming only that the model is observable. The decompositions depend on factorizations of the characteristic polynomial of the state evolution matrix G into relatively prime factors. This generalizes the method of West (1997 ) which considers one decomposition in the particular case where G is diagonalizable. Conditions are derived for a decomposition to be independent. These results show that no autoregressive process of order d has an independent decomposition for any integer d . Two illustrations of this procedure are discussed in detail.     

艺术建筑设计的探索

通过徐州一中艺术楼的设计实践，寻求优美而独特的艺术形象，并用纯几何形体的组合来达到功能与形式的完美统一。     

Measuring the errors of form of industrial surfaces: prediction and optimization

To acquire maximum information on the geometrical errors of industrially made surfaces at a minimum cost, a method for estimating conditional probabilities of a random signal (Bayesian prediction) is applied to three-dimensional metrology. First, a surface is interpolated between data acquired on a coordinate measuring machine (CMM). Then, for a given probability, limit surfaces are computed that bind a region of space containing the known data and the most probable interpolation of the missing data of the surface. These bounds can be treated as the surface; their points can be considered as if they were actual CMM data when fitting a tolerance zone or a datum feature to the data. For Bayesian prediction, the basic hypotheses on the signal are stationarity, ergodicity, and gaussian density. Deviations from these hypotheses and their consequences on the prediction are taken into account and corrections are proposed.     

机油泵转子的研究

本文研究了有关机油泵转子的齿形曲线、测绘及型腔设计等几个问题     

Colour extension properties of individual pigments and effects on shades of foundations in cake form

The mechanism of colour change during the pigment dispersion process and during powder application to the skin surface was studied by examining the colour extension properties of Yellow. Red , and Black iron oxides in white powder bases. A new measure for the evaluation of the degree of colour extension was devised. This measure corresponded well with human visual sensation, and was found to be useful for comparing the rates of colour extension of pigments. The rate of colour extension of pigments was found to vary in the order: Yellow acicular Red granular Red Black. This result explains colour darkening and the change towards reddish tones during the pigment dispersion process, because Yellow extends fully in the early stage of the process but Red , especially in granular form, and Black continue to extend even in the later stage. Acicular Red iron oxide is more favourably employed than the granular form to attain sufficient colour extension of foundations with lower energy expenditure, and to decrease the discrepancy between the cake colour and the colour of applied powder.
Le développement des oxydes de fer et effet sur les nuances des fonds de teint compacts     

月光之丽、变彩之奇的月光石

根据所藏月光石的光薄片鉴定研究，阐述了月光石的美学特征和产生原因。介绍了月光石的产出特征和相应的月光石文化，同时介绍了我国关于“和氏壁”属性与月光石关系的研究历史及现状。     

A singular loop transformation framework based on non-singular matrices

In this paper, we discuss a loop transformation framework that is based on integer non-singular matrices. The transformations included in this framework are called Λ-transformations and include permutation, skewing and reversal, as well as a transformation calledloop scaling. This framework is more general than existing ones; however, it is also more difficult to generate code in our framework. This paper shows how integer lattice theory can be used to generate efficient code. An added advantage of our framework over existing ones is that there is a simple completion algorithm which, given a partial transformation matrix, produces a full transformation matrix that satisfies all dependences. This completion procedure has applications in parallelization and in the generation of code for NUMA machines. This work was supported by the Cornell Theory Center, NSF Presidential Young Investigator award #CCR-8958543. by NSF Grant #CCR-9008526, and by a grant from the Hewlett-Packard Company.     

基于计算的工业喷涂机器人基本参数设计方法

设计与确定机器人参数需要在各项性能之间进行折衷,常常是一个耗时的迭代过程。本文提出了一种工业喷涂机器人基本参数确定的一般方法。通过喷涂机器人的设计与开发过程,基于机器人建模方法,归纳出机器人基本参数对各项性能尤其是工作空间特性的影响因素与规律,并在此过程中上分析了其结构参数对机器人工作空间和性能的影响,从而得出了机器人工作空间特性与结构参数之间的内在联系,为工业机器人的设计提供依据。