单点渐进成形工艺参数对激光拼焊板圆锥台件回弹影响研究

激光拼焊板单点渐进成形回弹是影响成形精度的重要因素。使用回弹角来度量板料回弹大小,并使用正交试验设计对工具头直径、成形高度、下压量、半顶角等因素进行实验研究,得到各因素对回弹的影响程度。得出影响板料回弹因素的大小依次为:成形高度、下压量、半顶角和工具头直径;工具头直径变化对回弹影响不大;成形高度对回弹影响显著,成形高度越高,回弹量越小;在一定范围内,回弹角的大小取决于下压量的大小,下压量越大回弹角越小;过大或过小的半顶角都会导致显著的回弹现象,合适的半顶角设计能够有效减少回弹的出现,从而保证成形精度。最后通过实验验证了正交试验得出的最优工艺参数。     

基于误差预测的机床精度分析与设计

数字化精度分析是当前确保机床设计精度的重要手段。精度建模与精度分析等重要手段主要针对机床几何精度、运动精度及工件表面成形运动精度。对于复杂成形运动机床,目前精度设计标准与工件加工精度之间尚无准确对应关系。为此,提出了基于误差预测的机床精度设计方案,该方案分为两阶段数字化精度分析。第一阶段通过技术系统实现工件到工艺系统各部件精度分配与检测,在规定的精度下达到机床输出精度。第二阶段通过机床系统完成机床输出到机床各组成部件精度分配与检查。文中以YK3610滚齿机为例,详细分析了两系统误差模型及应用方法,并通过试验验证机床的实际切割精度可达5-4-4等级,因此该方法为复杂成形运动机床精度的设计提供了依据。     

基于正交实验优化不锈钢表面纳米孔结构制备工艺

目的通过正交实验优化不锈钢表面纳米孔制备工艺。方法通过田口实验方法设计正交试验优化工艺。采用含有氯化钠和硫脲的硝酸溶液阳极氧化制备纳米孔,在含有氯化钠、盐酸和硫酸的水溶液中进行扩孔处理。通过扫描电子显微镜、能谱仪对表面处理后的试样表面形貌和元素进行分析,应用软件统计SEM图片孔隙率,并将孔隙率作为响应指标,利用极差分析和方差分析研究阳极氧化工艺和扩孔时间对表面形貌及孔隙率的影响,并优化工艺参数。结果 SEM照片和5个水平的均值表明,硝酸浓度的提高有利于提高孔隙率,较高的硫脲浓度有利于形成均匀有序的纳米孔结构,氯化钠浓度、氧化时间、氧化电压和扩孔时间对表面形貌和孔隙率影响不明显。元素分析表明,纳米孔的材料仍然是不锈钢,而不是金属氧化物。正交实验优化的工艺参数是:硝酸的体积浓度为90 mL/L,硫脲的质量浓度为3.5 g/L,氯化钠的质量浓度为20 g/L,氧化时间为120 s,氧化电压为5.0 V,扩孔时间为50 s。结论通过实验验证,优化后的工艺能够制备出表面较平整、孔隙率较高的纳米孔结构。     

电子束3D打印模型处理对钛合金零件成形精度的影响

模型处理是影响3D打印钛合金零件成形精度的关键因素之一。以电子束3D打印几种典型形状TC4钛合金零件为研究对象,通过对成形零件进行精度检测,分析其在模型处理过程中引起误差的来源,提出了几项改进措施:对于圆柱体轴类零件,将模型精度设置提高到0.02 mm,可有效提高零件的成形精度;对于点阵多孔零件,提高STL数据的精度并优化切层算法,保持切层前后模型原貌是解决该问题的途径;对于针状细圆柱零件,将相同零件按照同一方向摆放,可以减少摆放角度对偏差的随机性影响;对于异形件,应在满足成形精度的前提下合理布局并减少支撑;对于薄壁零件,增加支撑密度能够有效提高零件悬空部分的成形精度。     

Effect of prestressed ultrasonic peen forming parameters on bending curvature and spherical deformation of plate

The elastic prestressed ultrasonic peen forming (UPF) was adopted in order to solve problems of insufficient bending deformation and large spherical deformation of plate during free UPF. The theoretical analysis of prestressed UPF and the influence of elastic prebending moment on deformation were analyzed. Spherical deformation coefficient was defined to quantificationally describe the spherical deformation. Experiments were conducted to compare the differences between free UPF and prestressed UPF processes and the effects of processing parameters on bending curvature and spherical deformation coefficient were studied. The results show that peening trajectory in chordwise direction is beneficial to enlarging spanwise bending deformation and decreasing spherical deformation coefficient. Large prebending curvature is helpful to increase spanwise bending deformation and decrease chordwise deformation, thereby obviously decreasing spherical deformation coefficient. Large spanwise deformation can be obtained under large firing pin velocity, small plate thickness and small offset distance. Large firing pin velocity plays a positive role in decreasing spherical deformation, while plate thickness and offset distance have little effect on it. Above all, prebending curvature and peening trajectory are the most important factors during prestressed UPF process. This study provides guidance for parameters optimization of prestressed UPF for wing plate with large thickness.     

重庆某输气管道地铁杂散电流干扰检测评价与防护案例研究

重庆某输气管道沿线与多条地铁、轻轨交叉并行,管道阴极保护系统受干扰严重。为了认识管道沿线阴极保护水平和真实干扰情况,对其阴极保护参数进行了现场测试。根据测试结果,分析获得了管道沿线干扰大小的分布情况。基于分析结果,利用智能抗干扰恒电位仪开展现场馈电试验。结果表明,在合理分布辅助阳极地床的情况下,利用强制电流阴极保护和牺牲阳极相结合的方法可以将管道的干扰水平控制在可接受范围内。该研究成果可为油气管道动态直流干扰的分析和防护设计提供参考。     

Manufacturing of advanced smart tooling for metal forming

Forming is widely used due to its high efficiency in material utilization and its high production rate in general. Most forming processes control the geometry of final products through a set of tooling. The increasing demands on lightweight products have challenged the performances and functionalities of tooling. This paper provides a systematic review of recent advancements related to tooling performance and functionalities, including tool materials, tooling fabrication processes (e.g., machining, heat treatment, coating, surface texturing, and additive manufacturing), sensing, and data analytics. Finally, recommendations on future research directions for metal forming tooling are provided.     

基于设计性试验提升本科生自主创新能力——以土木工程材料实验课程教学改革为视角

实验教学是土木工程材料课程的重要环节,对学生掌握课程的理论知识、深刻理解材料性能具有极其重要的作用。根据课程特点,基于设计性试验,以设计性、综合性及创新性试验为主,验证性实验为辅,建立试验与实际工程相结合、试验与专业设计大赛相结合的多元化人才培养体系。通过实施开放与弹性的实验室管理制度,逐步提高学生的自主创新能力,以及分析和解决实际工程问题的能力。     

High-efficiency simultaneous extraction of rare earth elements and iron from NdFeB waste by oxalic acid leaching

Iron can not be recovered at high value because only rare earth elements are effectively recovered from NdFeB waste via oxidation roasting-hydrochloric acid leaching process.In this study,a new method for leaching NdFeB waste with oxalic acid was developed.The high-efficiency,simultaneous and high-value recovery of rare earth elements and iron was realized to simplify the process and improve the economic benefit.Results of the oxalic acid leaching experiments show that under the optimum leaching conditions at 90℃ for 6 h in the aqueous solution of oxalic acid(2 mol/L) with a liquid-solid ratio of60 mL/g,the iron leaching efficiency and precipitation rate of rare earth oxalate reach 93.89% and 93.17%,respectively.Rare earth oxalate and Fe(C₂O₄)3^3- were left in the residue and the leaching solution,respectively.The leaching mechanism was further analyzed by characterising the leach residues obtained through X-ray powder diffraction(XRD) and scanning electron microscopy-energy dispersive X-ray spectroscopy(SEM-EDS).Results of the leaching kinetics study indicate that the process of oxalic acid leaching follows the shrinking nucleus model,and the leaching kinetics model is controlled by the mixed factors of diffusion and chemical reaction.The leaching residue was calcined at 850℃ for 3 h and then decomposed into rare earth oxide,which can be directly used to prepare rare earth alloy via molten salt electrolysis.For the leaching solution,ferric oxalate solution was reduced using Fe powder to prepare the ferrous oxalate(FeC₂O₄-2H₂O).     

矿用锚链轮齿形加工方法对其使用性能的影响

说明了成形法加工锚链轮是使用其性能变差的关键因素 ,说明了展成法是锚链轮齿形加工的合理加工法。