A macro-meso constitutive law for concrete having imperfect interface and nonlinear matrix

The overall behavior of concrete depends on its meso structures such as aggregate shape, interface status, and mortar matrix property. The two key meso structure characters of concrete, bond status of interface and nonlinear property of matrix, are considered in focus. The variational structure principle is adopted to establish the macro-meso constitutive law of concrete. Specially, a linear reference composite material is selected to make its effective behavior approach the nonlinear overall behavior of concrete. And the overall property of linear reference composite can be estimated by classical estimation method such as self-consistent estimates method and Mori-Tanaka method. This variational structure method involves an optimum problem ultimately. Finally, the macro-meso constitutive law of concrete is established by optimizing the shear modulus of matrix of the linear reference composite. By analyzing the constitutive relation of concrete established, we find that the brittleness of concrete stems from the imperfect interface and the shear dilation property of concrete comes from the micro holes contained in concrete. Supported by the National Natural Science Foundation of China (Grant Nos. 50679022, 90510017, 50539090) and National Basic Research Program of China (Grant No. 2007CB714104)     

关于基体曲率的热障涂层残余应力分析

采用空心和实心四相同心圆模型,导出了轴对称温度应力状态下的位移公式,分析了基体曲率对热障涂层残余应力的影响。结果表明:热障涂层结构中各层内既有环向应力,又有径向应力,应力大小与温降成线性关系;当陶瓷层在外层时,在氧化层/陶瓷层和粘结层/氧化层界面上产生垂直界面的拉应力,且实心模型的拉应力远大于空心模型的拉应力;当陶瓷层在里层时,空心模型中相应界面上的应力为压应力。     

高性能电极接头栓的研制

研制了高粘结强度、低电阻率、高渗透性能接头栓,并说明了改进的目标和方向。研究了电极接头栓的使用性能、主要作用和选用接头栓补救电极和接头连接质量的优点;研究了电极接头栓的原料选择、原料配比、添加剂和发泡剂的选取;确定了电极接头栓的生产技术要求和生产工艺流程。试验证明,研制的高性能接头栓具有高粘结、强固结、有效补强的作用。     

钯－银合金膜分离氢气的研究

采用厚为５０μｍ的Ｐｄ／Ａｇ（２３）合金膜进行了氢气渗透系数的测定和Ｈ＿２／Ｎ＿２混和气分离的研究，得出温度、压力、膜厚、进料气流量、膜的预处理和再活化及膜表面中毒等因素对氢气渗透的影响。分离Ｈ＿２／Ｎ＿２混和气可获得高纯氢气。     

普光气田邻井干扰压降研究

根据普光气田现场资料,分析普光气田关井压降恢复时间和稳定生产时间的关系。建立邻井干扰计算模型,评价邻井干扰压降值及邻井干扰,并对邻井干扰规律进行敏感性分析。     

Interfacial Microstructure and Mechanical Properties of Al/Mg Butt Joints Made by MIG Welding Process with Zn-Cd Alloy as Interlayer

Butt joints between Mg alloy AZ31 B and pure Al 1 060 sheets were produced via metal inert gas welding process with Zn-Cd alloy foil. Crack-free Al/Mg butt joints between AZ31 B Mg alloy and pure Al 1060 sheets were obtained. Intermetallic compound layer 1 and layer 2 had formed in fusion zone/Mg alloy and the average thickness of the layer 1 was about 50 μm. The intermetallic compound layer 1 consisted of Al12Mg17 and Mg2Si phases while layer 2 consisted of Al12Mg17, Mg2Si and Mg Zn2 phases. The crack started from the IMC layer at the bottom of the joint and propagated along the brittle IMC layer, then expanded into weld metal during the SEM in situ tensile test. The highest tensile strength of the dissimilar metal butt joints could reach 46.8 MPa and the effect ofinterfacial IMC layer on mechanical property of the joint was discussed in detail in the present study.     

介质阻挡放电反应器降解邻二甲苯的特性研究

采用介质阻挡放电(DBD)降解常压下流动态的邻二甲苯模拟废气,系统地考察了放电极值电压,气体的初始质量浓度、停留时间以及相对湿度等工艺参数对邻二甲苯降解的影响,并初步探讨了邻二甲苯的降解产物.实验研究结果表明:在7.0kV的放电极间电压下,邻二甲苯的初始质量浓度为1 500mg/m3,停留时间为9s,其去除率可达到80%以上.降解产物主要为CO2、H2O以及苯甲酸、苯乙酸、苯乙醛等有机物,并且经降解后产物的生物可生化性得到提高,因而为后续的等离子-生物法联合处理VOCs提供了依据.     

On the gas dynamics of HVOF thermal sprays

An experimental study of the gas-dynamic aspects of the high-velocity oxyfuel (HVOF) thermal spray process has been performed using commercially available HVOF equipment (Hobart-Tafa JP-5000, Ho-bart-Tafa Technologies, Inc., Concord, NH). Optical diagnostic techniques, including microsecond-expo-sure schlieren and shadowgraph imaging, were applied to visualize the hot supersonic jet produced by this equipment without particle injection. Rapid turbulent mixing of the jet with the surrounding atmos-phere was observed, which is an issue of concern in coating quality due to the possibility of oxidation of sprayed particles. This mixing appears to be a function of the ratio of densities of the hot jet and the cold atmosphere as well as a function of the velocity of the jet, rather than one of combustion-chamber pres-sure or barrel length. The supersonic core of the HVOF jet dissipates rapidly due to the mixing, so that the jet is no longer supersonic when it impinges on the target surface being sprayed. Secondary issues also observed in this study include strong jet-noise radiation from the HVOF plume and the entrainment and induced bulk motion of the surrounding air.     

Image-based extended finite element modeling of thermal barrier coatings

Further advances in Thermal Barrier Coating (TBC) design are linked with the evolution of numerical models for TBCs. The present paper, therefore, enhances the idea of a currently available FEM package (OOF) that has been designed for microstructural level simulations. The approach of Extended FEM (XFEM) is incorporated in an in-house developed program to account for the existence of cracks in TBCs; both for stress-strain analysis and for heat transfer analysis. The new XFEM program is then employed to carry out the analyses of a YSZ deposit and a multilayered TBC to predict the effective Young's moduli, the overall thermal conductivities, and to assess the fracture behavior of the coating.