Impact behavior and fractographic study of carbon nanotubes grafted carbon fiber-reinforced epoxy matrix multi-scale hybrid composites

Carbon nanotubes are the most promising reinforcement for high performance composites. Multiwall carbon nanotubes were directly grown onto the carbon fiber surface by catalytic thermal chemical vapor deposition technique. Multi-scale hybrid composites were fabricated using the carbon nanotubes grown fibers with epoxy matrix. Morphology of the grown carbon nanotubes was investigated using field emission scanning electron microscopy and transmission electron microscopy. The fabricated composites were subjected to impact tests which showed 48.7% and 42.2% higher energy absorption in Charpy and Izod impact tests respectively. Fractographic analysis of the impact tested specimens revealed the presence of carbon nanotubes both at the fiber surface and within the matrix which explained the reason for improved energy absorption capability of these composites. Carbon nanotubes presence at various cracks formed during loading provided a direct evidence of micro crack bridging. Thus the enhanced fracture strength of these composites is attributed to stronger fiber–matrix interfacial bonding and simultaneous matrix strengthening due to the grown carbon nanotubes.     

Comparison of xylo-oligosaccharides production by autohydrolysis of fibers separated from ground corn flour and DDGS

Xylo-oligosaccharides (XOS) are known to have beneficial health properties, and are considered to be functional food ingredients. The objective of this study is to compare corn fibers separated from ground corn flour and distillers dried grains with solubles (DDGS) for XOS yield and optimum autohydrolysis conditions. Based on the initial xylan content, the fiber separated from ground corn flour (FC) resulted in higher XOS yield (71.5%) than the fiber separated from DDGS (FD) (54.6%) at the maximum XOS production conditions. XOS produced were mainly xylobiose and xylotriose. Based on total initial material also, FC resulted in higher XOS yield (8.9%) than FD (8.0%), based on total original masses. Thus, fiber separated from ground corn flour would be a better feedstock for production of XOS than fiber separated from DDGS. The conditions for maximum XOS production from FD and FC were 180 °C with 20 min hold-time and 190 °C with 10 min hold-time, respectively.     

An experimental approach towards increasing mechanical durability of extruded fish feed in the drying process

Mechanical durability of extruded fish feed must be optimized to lower economic losses as well as emission of organic matter to aquatic environments. The glass transition hypothesis for viscoelastic biopolymers is demonstrated and confirmed experimentally to be valid for extruded fish feed pellets. It is proposed and demonstrated that it is important to avoid early glass transition onset, to optimize the obtained mechanical durability. From the proposed glass transition hypothesis, immediate process relevance to the pre-drying transport mechanism is demonstrated. Furthermore, measured mechanical durability is found to range from 1.5 to 5.0% loss, for different combinations of drying parameters.     

Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

基于随机光栅的可调谐随机光纤激光器

提出一种基于随机光栅与高反射布拉格光栅(FBG)相结合的可调谐随机光纤激光器。利用980nm泵浦光源泵浦一段7m长的掺铒光纤(EDF)进行增益放大,由随机光栅提供随机反馈。随机光栅长7cm,具有约10000个折射率修改点,这些点由飞秒激光逐点写入,并沿光纤方向随机分布,两点相邻间隔小于10μm。同时,利用中心波长为1548nm的高反射FBG来组成半开放腔结构,实现了随机激光的输出。实验测得的泵浦阈值功率仅为18mW,斜率效率高达13.2%,并通过改变FBG的中心波长,实现了输出激光波长的可调谐,调谐范围为4.45nm(1548.04~1552.49nm)。得益于半开放式激光腔的设计和EDF的高增益,整个系统具有阈值低、效率高、结构简单等优点。     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

Crystallization and spectroscopic properties in Er3+ doped oxyfluorogermanate glass ceramics containing Na

The Er³⁺ doped oxyfluorogermanate glasses, with a composition containing Na element, were synthesized by the conventional melting–quenching technique. When Na element was introduced into the composition of oxyfluorogermanate glass, the crystals behavior was investigated in details. Depending on the annealing procedure supplied, thermal annealing of precursor glasses in the system GeO₂/BaF₂/AlF₃/Na₂O/NaF/ZnO/GdF₃/ErF₃ led to the precipitation of different crystal phase nanocrystals. It was confirmed the nanocrystals in GC600 is orthorhombic NaBaAlF₆ which led to enhance obviously in the UC luminescence of Er³⁺. However, the nanocrystals in G585 led to decrease in the UC luminescence, which indicated few Er ions enter into the lattice of this nanocrystal phase. The reason of the decrease in UC emission intensity of GC585 was analyzed.     

Design criterion for fatigue strengthening of riveted beams in a 120-year-old railway metallic bridge using pre-stressed CFRP plates

This study presents a design criterion developed for fatigue strengthening of a 120-year-old metallic railway bridge in Switzerland and presents a pre-stressed un-bonded reinforcement (PUR) system developed to apply the strengthening. The PUR system uses carbon fiber reinforced polymer (CFRP) plates; however, unlike conventional pre-stressed CFRP reinforcement methods, preparation of the existing metallic bridge surface is not required. This decreases the time required for on-site strengthening procedures. The principle of the constant life diagram (CLD) and two fatigue failure criteria (Johnson and Goodman) are described. Analytical formulations are developed based on the CLD method to determine the minimum CFRP pre-stress level required to prevent fatigue crack initiation. The PUR system uses an applied pre-stress force to reduce the mean stress level (and stress ratio) to shift an existing fatigue-susceptible metallic detail from the ‘at risk’ finite life regime to the ‘safe’ infinite life regime. The applied CLD method is particularly valuable when the stress history of the detail is not known and it is difficult to assess the remaining fatigue life. Moreover, it is shown that the currently adopted approach in many structural codes which emphasizes stress range as the dominant parameter influencing fatigue life are non-conservative for tension–tension stress patterns (i.e., stress ratios of 0 < R < 1). Analyses show that the modified Johnson formula accurately reflects the combined effect of stress range, mean stress level, and material properties, and offers a relatively easy design procedure. Details of a retrofit field application on members of a riveted wrought iron railway bridge are given. A wireless sensor network (WSN) system is used for long-term monitoring of the on-site CFRP stress levels and temperature of the retrofitted details. WSN measurements indicate that increases in ambient temperature result in increased CFRP pre-stress levels.     

Lipase‐catalyzed synthesis of aliphatic poly(β‐thioether ester) with various methylene group contents: thermal properties,crystallization and degradation

A series of novel aliphatic poly(β‐thioether ester)s with various methylene group contents were prepared by direct lipase‐catalyzed polycondensation of the monomer with an acid‐labile β‐thiopropionate group. The polycondensation reaction using immobilized lipase B from Candida antarctica was carried out in diphenyl ether at 90 °C. Poly(β‐thioether ester)s with high molecular weights of 20 500–57 000 Da and narrow polydispersities in the range 1.40–1.48 were obtained. Thermogravimetric analysis, differential scanning calorimetry and wide‐angle X‐ray diffraction were used to investigate the thermal properties and crystal structures of these polyesters. All the poly(β‐thioether ester)s were semicrystalline polymers and thermally stable up to at least 200 °C. In vitro degradation studies showed that they can rapidly degrade under acidic conditions by the hydrolysis of the β‐thiopropionate groups, suggesting their potential as acid‐degradable polymeric materials. © 2019 Society of Chemical Industry