船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

ARMA噪声中的正弦波检测

本文提出一种ＡＲＭＡ噪声中正弦波检测的方法，本方法先用改进的Ｐｒｏｎｙ法估计可能存在的正弦波，然后利用一种综合考虑衰减因子以及ＭＵＳＩＣ值的准则从估计结果中区分正统率波的真伪。数值例子表明，本文方法比Ｐｒｏｎｇ方法及ＭＵＳＩＣ方法具有更高的分辨力。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

PWM整流器高功率因数的实现

论述了交流斩波电路中控制部分的工作原理，并对该电路中电抗器的取值进行了计算。采用16位80C196KC单片机能使控制电路非常简单，并容易实现高频开关器件整流器的高功率因数。     

孔型热轧时轧制力的实用计算公式

采用修正系数法,利用板材在带刻槽的冲头进行深冲与平面冲头下深冲时的接触压力的比值确定孔型影响系数,进而推导出孔型热轧时轧制力的实用计算公式.     

结构化P2P网络中基于流言传播的负载均衡

提出了结构化P2P网络中利用结点间周期性的拓扑维护通信来夹带、传播消息进行负载均衡的方法，具体针对Chord系统从消息传播的速度和规模两个方面分析了该方法的性能，并利用仿真进行了验证。讨论了结论在其它形式网络中的推广和实现中的消息管理问题。     

固定式塔吊基础设计与施工技术

潘家园小区工程建筑面积3．6万m^2，地下3层，地上28层。基槽标高-10.750m，地面至屋面女儿墙上口高度为83m，地上标准层层高2．8m。采用土钉墙护坡，坡度1：0．1，该工程的地质条件适宜桩基础的施工。     

无粘结预应力卵形消化池的受力分析及设计

本文采用有限元计算分析软件ANSYS对近年来出现的卵形消化池进行计算分析,着重对卵形消化池在多种荷载下的内力与变形进行分析,并采用二次曲线模拟沿高度均匀变化的壁厚。提出适合卵形消化池结构预应力钢筋等效为均布荷载的计算与配筋方法,取得较好的结果。