悬浮法合成聚丙烯腈高吸水性树脂

以偶氮二异丁腈为引发剂，用悬浮聚合法合成了交联聚丙烯腈，然后对其进行水解，得到了高吸水性聚丙烯腈。交联剂用量和水解条件对树脂吸水倍数的影响很大。树脂吸去离子水倍数为420倍，平均粒径为250μm。     

高效液相色谱法测定卷柏中的穗花杉双黄酮

用反相高效液相色谱法测定卷柏提取物中的穗花杉双黄酮。结果表明：穗花杉双黄酮在质量浓度为41.2mg／L～206mg／L时，峰面积Y与其质量浓度X的线性关系良好，回归方程为Y=547．028X 15．4895(r=0.9999)，最低检测限为2．0μg/L；穗花杉双黄酮的平均回收率为99．42％(n=3)，相对标准偏差RSD为0．79％；连续进样、日内进样和日间进样所得检测结果的RSD分别为0．12％、0．11％和0．11％。     

反相高效液相色谱法测定meso-四苯基卟啉钴的纯度

采用反相高效液相色谱法测定合成meso-四苯基卟啉钴的纯度;以甲醇乙腈二氯甲烷(体积比为55∶35∶10)为流动相,ShimpackCLCODS柱(150mm×6.0mmi.d,5μm)为分离柱,流速为1.5mL/min,检测波长420nm;meso四苯基卟啉钴的测定在1.0～10μg/mL时线性关系良好(相关系数r=0.9993),加标回收率为97.03%～101.42%,重复进样的相对标准偏差RSD为0.64%～2.92%(n=5)。方法的准确度高,精密度好,实际应用效果好。     

3-D hydrodynamics generated in a stirred vessel by a multiple-propeller system

The aim of this study is to optimize the position and the number of propellers in a non-standard tall vessel. Laser sheet flow visualization experiments were carried out for selected geometrical arrangements which produced stable flow patterns and good transport between the propellers. Four double-propeller arrangements corresponding to frequent industrial cases and a three-propeller system have been chosen. Comparison of LDA measurements in the r-z plane, dimensionless global parameters N_Qp, Nt_m, N_p, E_p and spatial distribution of local energy dissipation rate ? shows that a three-propeller system is the most efficient.     

High temperature polymerization of propylene catalyzed by MgCl2‐supported Ziegler–Natta catalyst with various cocatalysts

Four cocatalysts, referred to as ethylaluminoxanes, were synthesized by the reaction between triethylaluminium (AIEt₃) and water under various molar ratios of H₂O/Al at ?78°C. Aluminoxanes were used as cocatalysts for a MgCl₂‐supported Ziegler–Natta catalyst for propylene polymerization at temperatures ranging from 70 to 100°C. When the polymerization was activated by AlEt₃, the activity as well as the molecular weight and isotacticity of the resulting polymer gradually dropped as the temperature varied from 70 to 100°C. When ethylaluminoxane was employed as the cocatalyst, good activity and high molecular weight and isotacticity were obtained at 100°C. Furthermore, when the cocatalyst varied from AlEt₃ to ethylaluminoxane, the atactic fraction and polymer fraction with moderate isotacticity decreased and the high isotactic fraction slightly increased, which indicated that the variation of the cocatalyst significantly affects the isospecificity of active sites. It was suggested that the reactivity of the Al‐Et group and the size of the cocatalyst were correlated to the performance of the Ziegler–Natta catalyst at different temperatures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1978–1982, 2006     

尿素生产中尿液的不稳定流动对尿素一分塔的影响

介绍了水溶液全循环法尿素生产系统中,一分塔的精馏段由泡罩塔盘改为规整填料后出现的一系列问题,针对尿液的不稳定流动造成一分塔规整填料严重腐蚀的原因,进行分析并提出整改和预防措施。     

15%田草灵高效液相色谱分析

采用Ｎｏｖａ－Ｐａｋ Ｃ１８不锈钢色谱柱进行反相液相色谱分析，以甲醇：水＝６５：３５（Ｖ／Ｖ）为注动相，以邻苯二甲醇二乙酯为内标物，用内标法测定田草灵除草剂中苄嘧黄隆和异丙甲草胺的含量，结果表明，各有效成分与内标物色谱峰分离完全，杂质无干扰，测定结果，苄嘧黄隆和异丙甲草胺的变异系数分别为０．７４％和１．０７％，回收率分别为９９．４％￣１００．８％和９９．１％￣１０１．３％。     

MATHEMATICAL MODELING OF THROUGH-HOLE-PLATING IN ELECTROCHEMICAL MICROFABRICATION II. AXISYMMETRIC TWO-DIMENSIONAL CONVECTIVE MASS TRANSFER

Axisymmetrical, two dimensional mass transfer in a tube and a through-hole was studied. The elliptic convective-diffusion equation was solved numerically by taking into account both the axial and radial diffusion in the entrance region of an infinite tube. The whole mass-transfer region in a tube of finite length was also studied by dividing the domain into several regions according to different mass-transfer mechanisms. A similar analysis is then conducted for a through-hole geometry by assuming a modified Hagen-Poiseuille fluid pattern. Results show that mass-transfer rate in a through-hole is larger than that in a tube by approximately 10%. This is due primarily to faster fluid flow within the concentration boundary layer in a through-hole.