Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

以表面负载季铵盐阳离子型苯/丙乳胶粒为模板制备ZrO_2空心微球

以C9油与甲基丙烯酰氧乙基三甲基氯化胺的共聚物P(C9-DMC)为乳化剂制备苯/丙阳离子乳胶粒,并以其为模板,利用直接包覆法制备了由17 nm左右微晶体堆成的ZrO2空心微球。所制得的样品采用FT-IR、XRD、TEM和SEM等进行了表征。     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

服装低密度聚乙烯热熔胶化学粉碎的研究

服装粘合衬布的生产需要低密度聚乙烯热熔胶的微细粉末,介绍了对该热熔胶的化学粉碎技术所进行的实验研究,表明采用适当的助剂种类和用量以及适宜的工艺过程,通过化学粉碎可以得到合格的粉末产品。     

热镀锌工艺对Ti-IF钢光整热镀锌板组织和性能的影响

在连续热镀锌线上研究了RTH带钢温度和光整延伸率对Ti—IF钢光整热镀锌板组织和性能的影响。试验表明，当RTH带钢温度在830℃以下时，成品铁素体晶粒度为10．0级，织构类型以{332}、{114}为主，随着带钢温度的进一步提高，热镀锌板的晶粒逐渐粗化，织构成为典型的{111}织构，且取向密度增加，r值随之提高，但当带钢温度在900℃以上时，织构又趋于无规则分布，r值显著降低；光整延伸率对Ti—IF钢光整热镀锌板力学性能的影响很大，随着光整延伸率的提高，屈服强度明显提高，n值明显降低，延伸率降低，抗拉强度变化较小，且光整延伸率对性能的影响与成品铁素体晶粒尺寸有关，成品晶粒越粗，光整延伸率的影响越大。因此对于Ti—IF钢光整热镀锌板而言，n、r值是一对矛盾体，在制订热镀锌工艺时，需根据使用条件的不同，对其n、r值进行综合考虑。     

The Region 1 & 3 Broadcasting‐Satellite Service Plan after WRC‐03

The 1977 Broadcasting‐Satellite Service (BSS) Plan for Region 1 & 3 had been widely acknowledged to be out‐of‐date by the late 1980s. Development of digital modulation in the early 1990s provided an opportunity to update the technical provisions of the Plan to make it more economically viable. After a decade of work and three World Radiocommunication Conferences (WRCs), the revision of Region 1 & 3 BSS Plan was finally completed in 2003. The new Plan increased channel assignments from 5 to 10 analog‐equivalent channels for each country in Region 1, and from 4 to 12 channels for each country in Region 3. Yet, despite the increase in capacity, the new Plan is surprisingly similar to the original one in terms of the technical parameters. It is still based on national coverage, and the channel plan, orbital location, orbital spacing, and polarization are also the same. As a result, the new Plan is no more economically viable to implement than the old. To create economically viable BSS systems would most likely require modifications to the assignment in the Plan. Yet, modification procedures were made more difficult to apply after replanning. Less future implementation of BSS networks than would otherwise have occurred can be expected, and an inefficient usage of these frequency bands will likely result. On the other hand, less implemented systems will mean more capacity set aside for future use. This is important for countries that currently do not have satellite operations. In the end, BSS replanning reflects the eternal conflict between efficient usage and guaranteed future access. Copyright © 2005 John Wiley & Sons, Ltd.     

热压/热变形Nd2Fe14B/α-Fe纳米双相永磁体的研究

为了制备各向异性块状Nd2Fe14B／α—Fe纳米双相永磁体，研究了热压／热变形工艺参数与样品微观组织结构、磁性能之间的关系。结果表明，饱和磁化强度Js随模压温度的升高而提高；而剩磁Jr、内禀矫顽力Hcj和最大磁能积(BH)max开始都随模压温度的升高而上升，但超过一定温度后反而降低；同时提高热压压力会使磁性能增加，而热变形温度对磁性能影响很小。热变形后样品垂直于压力方向的磁性能略高于平行于压力方向，呈现出轻微的各向异性。Nd2Fe14B／α—Fe纳米双相永磁材料在热压／热变形后没有产生晶粒的择优长大，在晶体学上仍然是各向同性的。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

Experimental Study on Polymer Artificial Bone with HA Coated and Fiber Liners

1Introduction HA(hydroxyapatite)wasakindofbioactiveceram ics,whichhadexcellentbiocompatibilityandtissueaffin ityinthatitscomponentsweresimilartothoseofhuman bone[1].Soitwasthebestknownhumanbonesubstitute,andunprecedentedeffecthadbeenharvestedinrecenttwo d…