液相还原法制备纳米银粉的研究

在液相联氨还原法工艺基础上，对液相还原法制备纳米银粉的还原反应条件（体系温度、分散剂、反应物浓度）进行了研究，得到了优化的反应条件；反应体系温度70℃，反应物浓度[Ag[NH3]2^ ]=0.02mol/l和特定的分散剂2^#。且冬季同平均粒径约为50nm、大小均匀、灰白色的球状银粉。     

Preparation and mechanical properties of Fe_3Al/Al_2O_3 nano-/micro-composite

1　INTRODUCTIONAlumina(Al2 O3)ceramicsareoftenconsideredforstructuralapplications,duetotheirpropertiesofhighhardness ,chemicalandwearresistanceandgoodmechanicalpropertiesatroomandhightemperature .Thewellknownlimitationfortheseceramics ,how ever ,istheverylowtoughness .Recentstudieshaveshownsignificantimprovementsinmechanicalprop erties ,includingtoughness ,byaddingductilesecondphaseparticles ,suchasNi,Al,MoandCu[14 ] .Anincreaseof 80 % 333%inthefracturetoughnesshasbeenreportedforAl2 O3…     

Optical Investigation of the Effects of Substrate Orientation on Oxidation of Single Crystal β-NiAl

The residual stresses in -Al₂O₃ scales formed on high-purity FeCrAl and FeCrAlY during oxidation at 1200°C and subsequent cooling and reheating were studied using photostimulated luminescence spectroscopy. Systematic measurements of the stress in the oxide were made as a function of both alloy thickness and cooling rate and the development of stresses in the oxide scale during thermal cycling was investigated as a function of the temperature. Depending on the ratio of the alloy and oxide-scale thicknesses, substantial stress relaxation was observed to occur during cooling at a rate of 8 K/min. Compressive growth stresses of 1 GPa were determined by comparing the residual-stress measurements at room temperature with those calculated based on thermal-expansion mismatch. No significant differences in the growth stresses, the total residual stresses, or the stress relaxation during thermal cycling were observed between the oxides formed on the Y-doped and undoped FeCrAl samples. Stress relaxation is also shown to lead to the development of tensile stresses in the oxide scale under certain conditions, in particular, those associated with slow cooling followed by rapid heating.     

The application of thermal sprayed coatings for pig iron ingot molds

Molds made of gray cast iron for casting pig iron ingots are subjected to severe temperature fluctuations. The main life- limiting factor for mold damage is the formation of surface cracks arising from thermal fa-tigue. Various flame and plasma sprayed coatings were investigated to extend the life of these molds. Coating materials studied include plasma sprayed ceramic coatings with bond coats as well as flame sprayed oxidation- resistant alloy powders. The results of cyclic furnace tests from room temperature to 1100 °C in air, simulating the thermal cycle in casting, indicated that failure occurred along the interface between the bond coat and the gray iron substrate because of iron oxidation, and not at the interface between the ceramic top coat-ing and the bond coating for a superalloy substrate. The field test results indicated that plasma sprayed alumina coatings with 200 μm top coating thickness are the most promising materials for pig iron casting.     

What do we mean by “catalytic activity”?

The relative reactivities of the lower alkanes in hydrogenolysis on a Pt/Al₂O₃ catalyst depend on the H₂ pressure used, as do those of a Ru/Al₂O₃ catalyst, pretreated in various ways, for propane hydrogenolysis. Apparent activation energies also vary with H₂ pressure. No single rate measurement adequately represents catalytic activity, which is properly defined as the rateconstant for the slow step.     

Mechanical Properties and Oxidation Behavior of Al2O3–AlN–TiN Composites

The study examines the effect which the composition of hot-pressed electroconductive ceramics has on their structure, mechanical properties, and oxidation behavior, for ceramics of the type AIN–Al₂O₃–42 wt% TiN, differing in the AIN/Al₂O₃ ratio. The results are physico-mechanical property data, including density, hardness, strength, fracture toughness, and wear resistance. A correlation was found between the wear resistance and fracture toughness. The analysis of oxidation products revealed the formation of α-Al₂O₃ and rutile in the temperature range from 600° to 1100°C and aluminum titanate above 1200°C. The spallation of the oxide layer caused low oxidation resistance of Al₂O₃-rich composites above 1250°C. The oxidation of composites was compared with the oxidation of pure TiN. The relationship is discussed between material properties, composition, phases, and processing parameters.     

抗水合氧化铝载体研究进展

氧化铝系载体用于含水或有水生成的催化过程时，均会发生再水合现象，从而造成催化剂强度的下降，并导致其比表面积大幅下降，使催化剂不可逆失活。镁铝尖晶石的抗水合性远高于氧化铝系载体，是一种很好的催化剂载体。综述了氧化铝系载体的再水合现象、改进载体抗水合性能的方法以及镁铝尖晶石粉体和载体的制备方法及改进措施。     

中铝瓷球的应用研究

本文以长石、粘土、矾土等天然矿物原料,采用可塑法成型工艺,研究了配方与烧结温度、瓷球密度、外观颜色的关系,研制成功了成本低、密度大、外观质量较好的中铝瓷球的较佳配方,并解决了瓷球生产中的关键工艺技术问题。     

氧化铝增强无机硅酸锌涂层的电化学阻抗谱研究

无机硅酸锌涂层是一种广泛使用的钢铁重防腐涂层。采用在涂料填料中加入氧化铝的方法可以得到具有更好耐磨性能的富锌涂层。本实验研究利用电化学阻抗谱法(EIS)研究了氧化铝的加入对涂层腐蚀防护性能的影响,结果表明氧化铝颗粒的加入使涂层的腐蚀防护性能略有提高。     

Processing of High-Density Submicrometer Al2O3 for New Applications

Sintered corundum components with submicrometer grain sizes exhibit properties which enable numerous new applications. Wet powder processing is developed to associate minimum grain sizes at highest densities with the lowest population of macrodefects. A closest ratio of powder particle size and sintered grain size is important for obtaining most fine-grained microstructures. This target was approached best by using powders with particle sizes in the range of 100–200 nm rather than with smaller nanoparticles.