对CFG桩质量缺陷的探讨

根据具体工程的概况及水文地质条件，分析了CFG桩在地下水位出现大面积缩颈现象和复合地基载荷试验达不到设计要求的原因，并介绍了地基补强措施，以满足工程质量的要求。     

高导电性原油电脱盐工艺研究

南阳原油中金属含量较高,掺有部分3次采油采出原油,加工时易造成电脱盐装置原油乳化,电导率高,脱盐难度较大。装置投产十几年来脱后含盐一直不合格,经过改造仍然超标,常压塔顶腐蚀严重。为此,对原油进行了电脱盐工艺条件及破乳剂研究,研制出了高效电脱盐设备和生物复合脱盐剂及降电流剂,采用平流弓形电极进行改造,解决了该原油的电脱盐问题,使脱后含盐达到3 mg/L。     

复混肥料中钾含量的测定

根据作者多年工作经验，详细介绍了复混肥料中钾合量的到定，且与标准GB／T8574—1988进行了逐一比较。     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。     

天然多糖类/蛋白质复合材料的研究进展

在参考了 31篇文献的基础上 ,详述了天然多糖类与蛋白质复合材料的研究进展     

原位插层聚合制备PVC/蒙脱土纳米复合材料

采用氯乙烯单体直接插层到蒙脱土中进行原位插层聚合，制备纳米复合材料，并用小角X射线衍射（XRD）、扫描电子显微镜（SEM）和电子探针技术对复合材料进行了结构表征。实验结果表明：采用原位插层聚合法制得的PVC／蒙脱土（MMT）复合材料为剥离型纳米复合材料。     

复合式水力旋流器油水分离实验研究

复合式水力旋流器将动态与静态旋流分离技术有机地结合在一起 ,具有动态与静态水力旋流器的双重优点。这种旋流器由动力组件 (包括电动机、空心驱动轴、旋转栅及溢流嘴等 )、静态旋流单体、入口腔、底流腔及溢流腔等部分组成。对额定处理量为 8m3/h样机的分离特性测试表明 ,当电动机驱动轴转速低于 30 0 0r/min时 ,入口压力为 0 10～ 0 35MPa ,底流压差为0 0 5～ 0 2 0MPa ,处理量为 3～ 10m3/h ,选用单螺杆泵增压和离心泵增压两种方式 ,分离效率分别为 97%和 84 % ,均取得满意的分离效果。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

Intermetallic compounds formed at the interface between liquid indium and copper substrates

The interfacial reactions between liquid In and Cu substrates at temperatures ranging from 175°C to 400°C are investigated for the applications in bonding recycled sputtering targets to their backing plates. Experimental results show that a scallop-shaped Cu₁₆In₉ intermetallic compound is found at the Cu/In interface after solder reactions at temperatures above 300°C. A double-layer structure of intermetallic compounds containing scallop-shaped Cu₁₁In₉ and continuous CuIn is observed after the Cu/In interfacial reaction at temperatures below 300°C. The growth of all these intermetallic compounds follows the parabolic law, which implies that the growth is diffusion-controlled. The activation energies for the growth of Cu₁₆In₉, Cu₁₁In₉, and CuIn intermetallic compounds calculated from the Arrhenius plot of growth reaction constants are 59.5, 16.9, and 23.5 kJ/mole, respectively.     

西霞院水利枢纽工程泄洪闸振冲碎石桩基础处理

通过西霞院水利枢纽工程泄洪闸振冲碎石桩基础处理施工方法论述,给出了加砂层振冲碎石桩施工造孔水压、水量、成孔速度、填料级配、填料方法以及振密电流值、留振时间等施工控制参数。