鼓风引射式燃气燃烧器的计算

提出鼓风式射式燃气燃烧器的基本计算公式与计算结果，并进行结构尺寸与工况分析，确定各种因素对其的影响程度。     

用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。     

乳化酸+硝酸粉末酸压技术在泥灰岩储层中的应用

华北油田泥灰岩储层曾进行多种类型的酸化增产改造工艺,但均未取得理想效果。经过对泥灰岩地层进行大量的油藏地质、室内试验研究以及工程、地质技术人员的反复论证,优选出一种切实可行的酸压改造措施——前置液+高温乳化酸+固体硝酸酸压工艺。经过现场应用,收到了较好的增产效果,为华北油田泥灰岩储层改造措施找到了突破口。     

高压注水管柱受力分析

进行高压注水管柱受力分析的目的就是根据注水条件研究注水管柱在不同过程中的各类效应，以及这些效应对管柱产生的受力和变形规律，从而明确注水管柱的工作状态，保障注水管柱有效合理地工作。较详细地分析了高压注水管柱在锚定、坐封以及注水3个过程中的受力状态和变形情况，并分析了高压注水管柱在不同过程中受到的各种效应的影响，推导出注水管柱在不同过程中的应力及变形的计算公式，并给出了算例。     

采用一次模压成形工艺生产高性能烧结NdFeB磁环

介绍了采用一次模压成形工艺批量生产高性能烧结钕铁硼磁环的新工艺 ,指出了目前该工艺仍存在的一些问题 ,同时概述了该工艺的应用前景     

Residual Stress Simulation of Injection Molding

In this study, distribution and history of residual stresses in plaque-like geometries are simulated based on linear thermoviscoelastic model, which helps to understand the mechanics and evolution of the residual stresses in the injection molding process. The numerical calculation of direction, combined with the specified boundary conditions. Results show that the stress variation across the thickness exhibits a high surface tensile value changing to a compressive peak value close to the surface, with the core region experiencing a parabolic tensile peak. Residual stress distribution throughout the thickness is almost same along the flowpath and the final residual stresses value near the gate is lower than the value near the end of flowpath.     

A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

Optimal control of accelerator concentration for resin transfer molding process

Resin cure following mold filling is an essential element in resin transfer molding. To fabricate a composite part with high dimensional stability and minimize residual stress, uniform resin cure should be achieved. This study considers a three-part resin system composed of epoxy, hardener and accelerator. The cure kinetics can be controlled by the accelerator concentration at the injection gate. A numerical method that can predict degree of cure distribution based on accelerator concentration at the gate was proposed. The degree of cure distribution is obtained by solving the resin flow, heat transfer, accelerator concentration and cure problems sequentially. Utilizing this numerical method, an optimal variation of accelerator concentration during mold filling was sought by solving a constrained optimization problem. The effect of accelerator control on degree of cure distribution was investigated and its validity was examined for two different geometries.     

喷煤未燃煤粉在高炉内行为的研究

在模拟攀钢高炉喷吹煤粉的生产条件下进行的未燃煤粉在高炉内的行为研究结果表明，在铁的直接还原、生铁渗碳、硅和钛还原、未燃煤粉和焦粉在炉渣中沉积、煤和焦炭反应性的各个试验中，未燃煤粉的反应性都大于焦炭，这些都是由于未燃煤粉的比表面积大，结构疏松所造成的。     

天铁炼铁技术进步

近十年来，天铁集团炼铁厂通过改善原燃料条件；优化炉料结构，提高入炉品位；采用提高炉顶压力、富氧喷煤、低硅冶炼、炉顶气象系统等多项先进技术，使高炉各项经济技术指标逐年提高。