掺杂改性对聚苯乙烯性能影响的研究

文章阐述了掺杂烷氧金属的聚苯乙烯的制备以及用红外光谱、扫描电镜和热分析分析其微观结构和热性能的部分研究结果。     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

二甲基硅油及其表面活性剂在化纤生产中的应用

综述了二甲基硅油及其表面活性剂在化纤油剂中的应用 ,化纤油剂应具有的高平滑性、高耐热等特性 ;介绍了改善油剂的综合性能及硅油表面活性剂用来提高纤维的可纺性等性能的方法。建议我国应尽快开发研制含硅油的化纤油剂     

The Interlaminar Bond Strength of Flexible Polymer-Metal Laminates

An alternative test method to the traditional 180° “T” peel test has been developed for the measurement of interlaminar bonding in three-ply (polyester/aluminium/polypropylene) flexible-packaging, laminate materials. The new test is thought to involve mixed mode I (opening) and mode II (shearing) failure, and takes into account the yielding of the polypropylene layer during testing. The method allows more direct comparisons between materials to be made, and allows the measurement of strong bonds, where a peel test would result in yield or fracture of the substrate arms before debonding.     

微波介质陶瓷的界面特性及其对介电性能的影响

详细地总结了界面的偏析、扩散和润湿性对微波介电性能的影响机理。并评述了粉末的初始状态、烧结工艺、添加剂(掺杂)和烧结方法等因素对材料界面特性的影响，进而影响到材料介电性能的研究进展。最后指出了在微波介质陶瓷界面研究领域面临的问题及今后的发展方向。     

有机硅氧烷改性水性聚氨酯的合成

采用有机硅氧烷单体与聚醚、二羟甲基丙酸（DMPA）和甲苯二异氰酸酯（TDI）反应制备水性聚氨酯涂料。研究结果表明采用后添加有机硅氧烷单体的合成工艺，可制备贮存稳定好的水性聚氨酯乳液；凝胶渗透色谱（GPC）分析表明有机硅氧烷改性水性聚氨酯提高了聚氨酯的相对分子质量；性能测试表明有机硅氧烷改性水性聚氨酯涂料具有明显的优点：涂膜硬度高，耐沾污性、耐水性好和耐溶剂性好。     

纳米白炭黑的表面改性及其在氯丁橡胶中的应用

研究纳米白炭黑经硅烷偶联剂(Si-75)湿法改性后对氯丁橡胶抗疲劳性能的影响，并对改性剂的用量、改性工艺条件进行了优化。实验结果表明：适当改性后的纳米白炭黑可显著提高氯丁橡胶的抗撕裂和抗疲劳性能。     

破乳剂浓度对聚合物驱原油乳状液破乳及界面性质影响

研究了嵌段聚醚型破乳剂对孤岛原油乳状液破乳和油水界面性质的影响。实验结果表明,对于三嵌段聚醚类破乳剂来说,破乳剂浓度在0~100 mg/L时,随着破乳剂浓度的增加,孤岛原油所形成的乳状液分水率增加,乳状液稳定性降低,破乳剂浓度继续增加,原油乳状液的分水率有所降低。而原油与含聚合物的水溶液间的界面张力随破乳剂浓度增加逐渐降低,界面剪切粘度有一最小值。界面张力及界面剪切粘度降低是乳状液稳定性降低与分水率增加的主要原因。     

界面扩展粘度的测量

介绍了界面扩展粘度κ的测定方法及其原理 ,列出了其相应的测定结果 ,同时对各种测定方法进行了分析与比较 ,并对它们的优缺点进行了讨论     

Surface modification of a biomedical poly(ester)urethane by several low‐powered gas plasmas

Several low‐powered gas plasmas were employed to treat a biomedical poly(ester)urethane using the treatment gases of CO₂, O₂, NH₃, and SO₂ with different treatment time (2, 5, 10, and 15 min). The changes of the physical and chemical characteristics of the biopolymer surface were studied. Surface morphology was evaluated by scanning probe microscopy, which showed increased roughness of the surface after plasma treatment. The wettability of the surface was examined by static water contact angle (SCA) measurements, which presented that there was a decrease of SCA in all plasma treatments compared with the untreated surface and that each gas plasma had an optimum treatment time accompanied by a minimum contact angle. X‐ray photoelectron spectroscopy indicated the changes of the surface functional groups. The data demonstrated that CO₂ and O₂ plasmas resulted in the incorporation of oxygen‐containing groups, while NH₃ plasma resulted in the combination of nitrogen‐containing groups, and SO₂ plasma resulted in the formation of sulfur‐containing groups. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1273–1282, 2006