Electric and dielectric properties of solution-gas interface-grown PbS films

Dielectric properties andI–V characteristics of solution-gas interface-formed PbS thin-film capacitors (Al/PbS/Al) of various thicknesses have been studied in the frequency range 10-10⁶ Hz at various temperatures (300–443 K). Current-voltage (I–V) characteristics show space-charge-limited conduction. Dielectric constant (ε) increases with increasing film thickness and temperature and decreases with increase of frequency. The loss factor (tanδ) peaks observed in tanδ vs frequency and tanδ vs temperature reveal relaxation effect from dipolar orientation. These maxima shift to higher-temperature region with increasing frequency. The large increase in capacitance (C) and dielectric constant (ε) towards low-frequency (f) region indicates the possibility of an interfacial polarization mechanism in this region.     

Comparison of interfaces in Ti composites reinforced with uncoated and TiB2/C-coated SiC fibres

Interfaces play an important role in determining the mechanical properties of composite materials. The interfaces established between a titanium-alloy matrix (Ti-6Al-4V) and uncoated and TiB₂/C-coated SiC fibres are analysed by scanning electron microscopy, transmission electron microscopy and X-ray techniques. Emphasis is placed upon the interfacial morphology and microstructure, identification of reaction products, and the stability of the coating layer. Complex multi-reaction layers are observed frequently in the interfacial zones. Previous, often contradictory, reports about the interlayers are reviewed. Experimental observation demonstrates that the type and distribution of interlayers vary in a given system, due to prolonged treatment of the samples at temperature. The formation and distribution of the interlayers are discussed further, with respect to these and previous findings. Methods of reducing interfacial reactivity are discussed.     

A relation between interfacial and bulk properties along the saturation curve

A liquid-vapor interface in thermal equilibrium was considered, where the pressure tensor depends upon the density (z) and the position z. The surface tension coefficient results are parametrized with the bulk compressibility, liquid-vapor density difference, and interfacial width along the saturation curve. Previous results at the triple and critical points reported by other investigators are verified. Also included is a plot of the computed results using the parametric equation and experimental data for different substances.     

An enhanced,acoustic emission-based,single-fiber-composite test

In the single-fiber-composite (SFC) test, a fiber imbedded in a matrix is loaded in tension, resulting in a fragmentation of the fiber. In the conventional version of this test, the final fiber fragmentation length distribution is used with a micro-mechanical model to determine the average fiber/matrix interfacial shear stress. In the enhanced version of this test, one also determines the applied stress at each fiber fracture, and from this, one can evaluate the strength of the fiber at short gage lengths. In our measurement system, we utilize an acoustic emission (AE) technique to detect the fiber fractures and to locate the fiber breaks and so determine both the fiber failure stresses as well as the fiber fragmentation lengths while the test is in progress. Critical to the success of this test is a broadband AE system that utilizes point-like AE sensors, procedures for evaluatingin situ, the wavespeed of the first wave arrival and signal processing techniques for determining the arrival time of this signal as precisely as possible for a broad range of wave shapes. Here we describe the application of such an enhanced SFC test procedure to investigate the failure of a Nicalon fiber in an epoxy matrix.     

硅烷涂层提升钢纤维-砂浆界面性能的试验研究

为了提升钢纤维-砂浆界面的黏结性能,采用9种基于硅烷的表面处理剂对钢纤维进行浸渍处理并高温固化成膜;埋置于水泥砂浆圆柱体试块中,开展单根纤维拉拔试验,获得拉拔荷载-位移曲线. 试验结果表明,采用不同的硅烷涂层对钢纤维进行表面改性,可以不同程度地改善钢纤维-砂浆界面的黏结性能;拉拔峰值荷载最高增加5.75倍,拉拔能耗最多增加2.48倍. 硅烷Z6011和Z6020及复合涂层能够较大幅度地提升界面黏结强度,主要增加钢纤维与砂浆界面的化学黏结力;硅烷Z6030和Z6040及复合涂层对界面黏结强度的提升幅度相对较小,主要增加界面滑移摩擦力. 采用扫描电子显微镜（SEM）研究界面黏结性能的提升机理,发现硅烷涂层使得界面过渡区的微观结构更致密,显著提升了钢纤维-砂浆之间的黏结性能.     

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR) including the gas holdup, volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature, p H and superficial gas velocity. The reactor diameter and height were 11 and 30 cm,respectively. It was equipped with a single sparger, operating at atmospheric pressure, 20 and 40℃, and two p H values of 3 and 6. The height of the liquid was 23 cm, while the superficial gas velocity changed within 0.010–0.040 m·s~(-1) range. Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase. The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution. The gas holdup was calculated based on the liquid height change, while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD) in different superficial gas velocities. The results indicated that at the same temperature but different p H, the gas holdup variation was negligible, while the liquid-side volumetric mass transfer coefficient at the p H value of 6 was higher than that at the p H = 3. At a constant p H but different temperatures, the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃ were higher than that of the same at 20℃. A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla) in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.     

无机盐对新疆油田三元复合驱界面性能影响研究

界面性能对复合驱提高采收率有重大的影响,界面张力越低,洗油效率越高;Zeta电位越高,油水乳状液越稳定。研究了各类无机盐对新疆油田复合驱界面性能的影响。结果显示,Zeta电位的绝对值随着无机盐浓度的增高而增大;无机碱中,碳酸根离子降低界面张力效果最好,氢氧根次之,碳酸氢根最差;阳离子中,钾离子降低界面张力效果最好,其次是钠离子,镁离子会略微提高界面张力,钙离子则会大幅度提高界面张力;阴离子中,与硫酸根相比,氯离子能更好地降低界面张力。通过以上研究,确定了Q站污水处理站外排水更适合三元复合驱配液。     

Interfacial energy and match of cold pressure welded Ag/Ni and Al/Cu

The technology of cold pressure welding was adopted to achieve the bonding of Al/Cu(limited soluble and forming compounds),Ag/Ni(hardly mutual soluble),and the relative state of interface was tested by HREM.The results indicate that stable interface is always corresponding to the low interfacial energy value;the stable interface is not coherent but partly-coherent because of the twisting of grain boundary caused by pressure,meanwhile existing dislocation.Namely,the interfacial match and other states under the condition of cold pressure welding are different from the situation that under the condition of thermal action.Moreover,theoretical analyses and calculation on the base of thermodynamics,crystallogeny ,solid physics etc,were discussed.     

PHYSICAL SIMULATION OF INTERFACIAL CONDITIONS IN HOT FORMING OF STEELS

1.~nonNUInericalmodellingbythefiniteelement(FE)methodhasbecomeaneffectiveandeconomyicmeansforsimulatingmetalfoeingprocesses.However,accuratemodellingdemandsthecorrectdefinitionandinputsofthedataforthethermalandphysicalpIDPertiesoftheworkpieceandtoolmaterials,theboUndaryconditionsattheworkpiece--toolinterfaceandinotherareas,inadditiontoappropriatemeshgenerationandnumericalsolutions.Althoughmostofthematerialdataareavailable,thedataforinterfacialheattransferandfrictionconditions,Whichhavesubst…     

STRAIN INDUCED STRUCTURAL TRANSITION OF INTERFACES AND TWINS IN A HOT－DEFORMED DUAL－PHASE TIAL ALLOY

ＳＴＲＡＩＮＩＮＤＵＣＥＤＳＴＲＵＣＴＵＲＡＬＴＲＡＮＳＩＴＩＯＮＯＦＩＮＴＥＲＦＡＣＥＳＡＮＤＴＷＩＮＳＩＮＡＨＯＴ－ＤＥＦＯＲＭＥＤＤＵＡＬ－ＰＨＡＳＥＴＩＡＬＡＬＬＯＹＣＨＥＮＧｕｏＦｉａｎｇ；ＷＡＮＧＪｉｎｇｕｏ；ＺＨＡＮＧＬｉｃｈｕｎａｎｄ...