Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

反向凝固法生产H90-钢-H90复合带

研究H90-钢-H90反向凝固复合过程中复合层厚度的变化规律以及复合带的组织和性能，探讨界面结合机理。结果表明：随着浸渍时间的增加，复合层的厚度变化经历了凝固生长、平衡相持和回熔3个阶段，钢带的预热温度越低，获得的最大复合层厚度越厚；H90复合层的组织为等轴晶粒，复合界面处Cu和Fe发生了扩散，而Zn未发生明显扩散，扩散层较薄，约为4μm；复合带的界面结合牢固；不同复合层厚度的复合带，其力学性能略有差异，但均达到GB5213——85所规定的F级深冲钢板的力学性能要求。     

Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

弹药包装冲击强度试验方法的改进研究

介绍一种新的弹药包装冲击强度试验方法，应用该试验方法可以防止冲击强度试验时出现与期望值相反的现象。     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

热轧高强钢平整机辊径参数设计技术研究

基于高强钢平整机的生产工艺特点,结合板形与辊耗问题,将带材的出口前张力与辊间压力横向分布都均匀作为目标函数,把保证所有被平整高强钢产品的机械性能满足产品大纲要求作为约束条件,提出了一套针对热轧高强钢平整机的工作辊与支承辊辊径参数设计模型.其研究结果对指导宝钢分公司1880 mm热轧平整机的工艺参数的确定与技术谈判发挥了重要作用,并具有进一步的推广价值.     

单桩腿有限元分析

为保证桩腿在冬季冰区海域的安全使用,对桩腿结构进行冰载荷作用下的强度分析。应用ANSYS软件建立桩腿、地基、冰相互作用的仿真计算模型,实现桩腿的力学分析。对桩腿进行了强度校核,计算出冰载荷作用下桩腿的变形及其应力状态。计算结果表明,桩腿在此冰载荷作用下强度满足安全要求。     

WSP特殊螺纹接头油井管的研制

介绍了WSP特殊螺纹接头的基本结构和设计思想,运用有限元方法,重点论述了密封设计和连接强度设计的方法和准则,并通过全尺寸试验进行了验证。计算和试验结果表明,该接头具有先进的螺纹形式、合理的扭矩台肩和金属/金属密封结构,有效地克服了API圆螺纹和偏梯形螺纹的不足,螺纹达到了与管体等强度,气密封能力达到了管体的内壁屈服压力。研究结果可以为开发更多适合油气田实际的特殊螺纹接头油井管提供参考。