Specific features of thermal decomposition of ammonium perchlorate subjected to γ radiation

Results of studying thermal decomposition of ammonium perchlorate (AP) samples in the original form and after irradiation by γ-quanta of ⁶⁰Co by methods of differential scanning calorimetry and dynamic thermogravimetry with heating rates b = 0.1–0.3 K/sec are described. Irradiation is performed in air at a temperature of 298 ± 2 K and a dose rate of ≈0.2 Gy/sec in the range of absorbed doses D = 0–150 kGy. Preliminary irradiation is demonstrated to lead to substantial transformations of the pattern of thermal decomposition of ammonium perchlorate in the dynamic regime of heating: the single-stage process of decomposition of non-irradiated samples proceeding at b = 0.107 K/sec in the temperature range of 625 to 743 K is replaced by a multistage process. At D = 150 kGy, exothermal transformations accompanied by noticeable losses of sample mass are observed starting from 473 K. Within experimental errors, the total thermal effect of AP decomposition is found to be independent of the absorbed dose and amounts to −1150 kJ/kg on the average. __________ Translated from Fizika Goreniya i Vzryva, Vol. 43, No. 6, pp. 69–74, November–December, 2007.     

超细六硝基芪的热分解性能

为了解超细六硝基芪（HNS）的热分解性能，通过DSC—TG实验研究HNS—IV的热分解过程，用Kissinger法和Ozawa法计算了HNS-Ⅳ热分解反应动力学参数。结果表明，HNS-Ⅳ的热稳定性与HNS-Ⅱ相当。Kissinger法和Ozawa法得到的HNS-Ⅳ分解表观活化能分别为221．4kJ／mol和220．3kJ／mol，比静态气氛下HNS-Ⅱ热分解反应的表观活化能减小27kJ／mol。     

Measurement of intrinsic rates for homogeneous gas‐phase reactions at high temperatures

A coiled quartz tubular reactor has been designed to measure the intrinsic reaction kinetics for homogeneous reactions at high temperatures up to 1100°C. Actual gas residence times were less than 100 ms. A simple and well‐studied test reaction (i.e., the decomposition of nitrous oxide, N₂O), with published intrinsic kinetics, was used to verify the operation of the experimental reactor. For this system, Peclet numbers (Pe = uL/DL) computed from experimental conversion data were greater than 1000, indicating that the plug flow assumption could be used with this reactor system to determine intrinsic rate expressions with errors of less than 5% for the conditions studied.     

Thermogravimetric analysis of methyl methacrylate‐graft‐natural rubber

The thermal degradations of methyl methacrylate‐graft‐natural rubber (MG) at different heating rates (B) in nitrogen were studied by thermogravimetric analysis. The results indicate that the thermal degradation of MG in nitrogen is a one‐step reaction. The degradation temperatures increase along with the increment of heating rates. The temperature of initial degradation (T₀) is 0.448B + 362.4°C, the temperature at maximum degradation rate, that is, the peak temperature on a differential thermogravimetric curve (T_p) is 0.545B + 380.7°C, and the temperature of final degradation (T_f) is 0.476B + 409.4°C. The degradation rate at T_p is not affected by B, and its average value is 48.9%; the degradation rate at T_f is not affected by B either, and its average value is 99.3%. The reaction order (n) is 2.1 and is not affected by B. The reaction activation energy (E) and the frequency factor (A) increase along with B, and the apparent reaction activation energy (E₀) is 254.6 kJ/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2952–2955, 2002     

CO2置换CH4水合物中CH4的实验和动力学

在自行设计的反应装置中考察了2.8 MPa和3.25 MPa压力下，温度271.2、273.2和276.0 K时CO2气体置换十二烷基硫酸钠（SDS）体系CH4水合物中CH4的置换过程。实验数据表明，在反应的前50 h，CH4水合物的分解速率较快，其后分解速率变慢。冰点以上CH4水合物的分解速率较快。基于动力学数据，建立了SDS体系置换反应过程中CH4水合物的分解动力学模型和CO2水合物的生成动力学模型。计算得到CH4-CO2置换反应过程中CH4水合物的分解活化能为28.81 kJ·mol-1，CO2水合物的生成活化能为68.40 kJ·mol-1。数据表明，CH4水合物的分解可能受置换反应过程中水分子的重排控制，而CO2水合物的生成可能受CO2气体在水合物中的扩散控制。     

Nd(OR)_3催化异戊二烯聚合动力学及聚合物结构

研究了Nd(OR)_3—A1(i—Bu)_3一A1Et_2Cl体系催化异戊二烯聚合的动力学和所得聚异戊二烯的分子结构。结果表明,本体系的有效利用率为6％左右。在Al(i—Bu)_3用量较高时,主要发生活性中心向A1的链转移;在A1/Nd≤20,聚合温度低于室温条件下可获得“活的”聚合物。聚合物分子量高、分布宽,主要受A1(i—Bu)_3用量和聚合温度影响。分子量分布宽与其GPC图呈双峰有关。催化剂的相分离实验表明,体系中有两种不同的活性种存在:高活性生成高分子量聚合物的固相活性种和低活性生成低分子的可溶性活性种。聚异戊二烯的顺1,4—链节含量在95％左右,其余为3,4—链节。     

球形LiMn1.5Ni0.5O4材料的嵌脱动力学

为明晰Li Mn1.5Ni0.5O4正极材料的动力学性能,采用水热辅助共沉淀法合成了尖晶石Li Mn1.5Ni0.5O4正极材料,并采用扫描电镜(SEM)、X射线粉末衍射(XRD)和电化学阻抗(EIS)研究了材料的结构和锂离子嵌脱动力学.实验结果表明:共沉淀法制备的Li Ni0.5Mn1.5O4材料颗粒呈均匀球形,且平均粒径较小,粒度分布较窄.在循环过程中,Li Ni0.5Mn1.5O4的电荷转移电阻增大,锂离子扩散系数减小,进而电子电导率和离子电导率下降.温度升高后,Li Ni0.5Mn1.5O4材料的溶液电阻变化不大,但是电荷转移电阻逐渐增大,锂离子扩散系数逐渐减小;此外,随着温度的升高,Li Ni0.5Mn1.5O4材料的溶解速度加快,从而导致SEI膜的厚度增大.Li Ni0.5Mn1.5O4材料的嵌脱锂动力学与温度和循环次数有密切关系.     

装载机变速箱运动仿真与动力分析

为了提高工程车辆研制设计中的技术分析与性能模拟水平,运用三维实体设计软件Pro/Engineer完成了轮式装载机变速箱零件三维造型设计和总成零部件装配连接;根据装载机变速箱前进II档运输工况牵引性能实验获得的速度与动力变化参数,运用Pro/Mechanism的运动仿真与动力分析功能,实现了装载机变速箱在实际动力驱动下的运动仿真与动力分析,检验了变速箱总成零部件的运动与动力特性,提高了工程车辆研制开发技术分析与性能模拟水平.     

Fabrication and adsorption property of novel adsorbent for potential application to wastewater with Fe（Ⅲ） ions

The spherical macroporous cellulose（SMC） was fabricated using medical absorbent cotton as raw material and nano CaCO3 as porogenic agents.And then,the phenylglycine was grafted onto the SMC to obtain the novel spherical macroporous cellulose derivative adsorbent（PSMC）.FT-IR and scanning electron microscope（SEM） were employed to characterize the adsorbents and Fe3＋ ions served as model solute to evaluate the adsorption property of the adsorbents.The experimental results show that the amount of porogenic agents and the value of pH have obvious influence on adsorption capacity of the adsorbents.The data of adsorption kinetic and isotherm display that the adsorbents possess excellent equilibrium adsorption capacity（348.94 mg/g） and have a bright prospect and considerable potential in the treatment of Fe3＋ ions in wastewater.     

基于表面反应和扩散迁移控制的灰岩单裂隙渗流—溶解模型及其数值模拟

针对碳酸盐类可溶岩地区水电站坝址流场、化学场以及固相介质属性等随时间发生改变,从而对工程安全运行造成不利影响等问题,研究了灰岩地区地下水运移过程中各物理场间的相互作用,分析了影响灰岩溶解速率的两个因素,即表面反应控制和扩散迁移控制。在此基础上,建立了单裂隙中的渗流—溶解耦合模型,并进行数值求解。模拟结果表明,在垂直裂隙延伸方向,其溶蚀锋面为非齐整平面,而是呈似“虫洞”状非均一变化,而沿裂隙延伸方向即自上游侧向下游方向溶蚀程度逐渐减轻;而通过裂隙的流量呈现随时间逐渐增大的趋势,但变幅不大;根据流量求得的等效水力隙宽,其增幅和增长速率均小于实际平均隙宽;同时,化学场中Ca2+浓度的分布与裂隙开度变化具有相似性,不同时刻下上游侧反应速率R均大于下游侧。就反应机制而言,在初期均受表面反应控制,而随反应进行,位于上游补给区部位转为受扩散迁移控制,但在下游位置仍受表面反应控制。