Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

基于中红外QCL的痕量CO气体传感器

为了减少CO爆炸给国民经济造成的巨大损伤,提出了一种能够快速地监测环境空气中痕量CO的气体传感器。由于CO分子基频吸收谱带的吸收线强要比泛频带和组合频带的吸收线强高出2～3个数量级,选择激射中心波长为4.65μm中红外量子级联激光器（QCL）作为光源,同时再配合长光程Herriott气室提高了CO体积分数检测下限。同时,该传感器采用单光源双探测器差分光学结构,消除了电调制光源所带来的不稳定性。实验表明：该传感器CO体积分数检测下限为2×10-6,并且操作人员可以通过替换在不同波长下运行的中红外QCL来测量其它气体。     

浅谈玻璃钢的加工

本文在实际研究和应用的基础上，对玻璃钢的传统加工方法和特种加工方法，如激光切割、纯水射流切割和磨料水射流切割作了简要论述。     

基于GP2Y0A02距离测量的仿真与辅助设计

为了实现非接触距离测量,利用多个仿真与设计软件设计了采用GP2Y0A02模块的距离光学测试系统。在PROTEUS中测量GP2Y0A02电压值,并在Matlab中采用多元线性回归建立GP2Y0A02电压与距离的拟合曲线,最后在开发的测量程序中利用拟合曲线求解得到距离量。测试结果表明,对于非线性位置测量采用适当数据处理方法能得到满意的测量精度。     

Monitoring slope deformation using a 3-D laser image scanning system:a case study

An ILRIS-36D 3-D laser image scanning system was used to monitor the Anjialing strip mine slope on Pingshuo in Shanxi province.The basic working principles,performance indexes,features and data collection and processing methods are illustrated.The point cloud results are analyzed in detail.The rescale range analysis method was used to analyze the deformation characteristics of the slope.The results show that the trend of slope displacement is stable and that the degree of landslide danger is low.This work indicates that 3-D laser image scanning can supply multi-parameter,high precision real time data over long distances.These data can be used to study the distortion of the slope quickly and accurately.     

树脂增强选择性激光烧结多孔金属件的研究

针对选择性激光烧结(SLS)间接方法成型的金属零件形坯,经脱脂和高温烧结后形成的零件存在大量孔隙和空洞,其致密度和强度都较低,不能满足实际应用要求的问题,采用改性耐高温环氧树脂浸渗零件烧结坯的方法,使多孔金属件致密化,并粘结内部金属网架,提高零件的机械性能.对浸渗烧结坯的拉伸强度的测试和扫描电镜(SEM)以及热失重(TGA)的分析结果表明,浸渗树脂后的烧结坯拉伸强度提高了约4倍;改性环氧树脂和金属网架粘结在一起,形成一个密实的网络结构,致密度大幅提高;零件可在200℃的温度下使用.该方法可以制造注塑模具和功能零件.     

Investigation of Flow Patterns in Continuous‐flow Stirred Vessels by Laser Doppler Velocimetry

The flow structure of a continuous‐flow reactor stirred by a Rushton turbine was investigated by laser Doppler velocimetry for two different mean residence time‐mixing time ratios. Velocity measurements were obtained for two inlet locations, corresponding to the incoming liquid stream being fed co‐currently or counter‐currently to the flow discharged by the turbine. In all investigated configurations and for all operating conditions, it was found that the flow disruption caused by the incoming liquid stream was observable mainly in the first vessel quarter, which followed the feed‐tube plane. From comparison of the velocities encountered in the various planes in the continuous‐flow reactor to the velocities of the batch reactor, it was also concluded that it may be possible to intensify the usage of the turbine‐stirred vessel by decreasing the characteristic times ratio, without considerable flow by‐pass and/or short‐circuiting problems.     

Effects of laser heat treatment on the fracture morphologies of X80 pipeline steel welded joints by stress corrosion

The surfaces of X80 pipeline steel welded joints were processed with a CO2 laser, and the effects of laser heat treatment （LHT） on H2S stress corrosion in the National Association of Corrosion Engineers （NACE） solution were analyzed by a slow strain rate test. The fracture morphologies and chemical components of corrosive products before and after LHT were analyzed by scanning electron microscopy and energy-dispersive spectroscopy, respectively, and the mechanism of LHT on stress corrosion cracking was discussed. Results showed that the fracture for welded joints was brittle in its original state, while it was transformed to a ductile fracture after LHT. The tendencies of hydrogen-induced corrosion were reduced, and the stress corrosion sensitivity index decreased from 35.2% to 25.3%, indicating that the stress corrosion resistance of X80 pipeline steel welded joints has been improved by LHT.     

激光熔覆含SiC金属陶瓷涂层显微组织特征

采用连续ＣＯ２激光器在钢表面进行熔覆含ＳｉＣ金属陶瓷涂层。对不同工艺条件下激光熔属层组织结构、成分与硬度进行了研究，对试验结果和凝固过程进行了传热分析。     

反射衰减诊断激光光束的应用分析

介绍了普通光学元件反射诊断激光光束的应用,提出了利用平面平晶的平面反射进行光能衰减,详细论述了采用该方法进行光能衰减的可行性,分析了平面平晶反射衰减中反射光S偏振态和P偏振态能量的差异,对激光束诊断的影响和解决方法,结合半导体绿激光器的光束诊断进行了应用分析。实验证明,该方法结构简单、调整方便、误差小,利用普通平面平晶反射衰减即可满足激光强度的匹配要求,实现了待测激光束无失真取样,达到很好的测试效果。