测距仪中新型的脉冲激光光源

针对现有测距仪中脉冲激光器存在寄生多脉冲的问题，提出并实现新型的采用同步泵浦声光调Q方法的测距仪用激光器、消除了寄生脉冲并提高了激光器的峰值功率。     

飞秒激光烧蚀研究进展

介绍飞秒激光烧蚀材料的机理论模型，阐述飞秒激光烧蚀的特性，揭示飞秒激光烧蚀的广泛应用前景。     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

激光武器对抗效能指标体系研究

武器系统的效能是规划、研制、配置和部署武器系统的基本依据,是评价武器系统优劣最重要的综合性指标,建立正确的效能指标体系是进行效能分析与评价的前提。在详细研究了激光武器对抗机理、效能指标选用原则的基础上,构建了相对完整的激光武器对抗效能指标体系结构,并提出了在不同作战任务下量度激光武器对抗能力的效能定义。     

Al_(10)Zn_(2.9)Mg_(1.7)Cu超高强铝合金的喷射成形制备研究

采用喷射成形技术制备了Al1 0 Zn2 .9Mg1 .7Cu高强高韧铝合金沉积坯件 ,研究了喷射成形制备过程中各工艺参数对沉积坯件的成形性、显微组织、致密度的影响 ,确定了适当的工艺参数 ,研究了沉积坯件的热挤压及热处理工艺 ,对材料的组织进行了分析并对不同状态的材料性能进行了比较。研究结果表明 :当喷射成形工艺参数合理时 ,沉积坯件具有良好的成形性与致密度 ,在随后的热挤压过程中 ,通过较低的挤压比即可使材料达到全致密 ;通过对合金进行适当的热处理 ,材料的极限抗拉强度达到 810MPa ,同时延伸率保持在 8%～ 11% ,该材料是一种理想的轻质高强结构材料。     

Modelling and analysis of 3-D arrangements of particles by point processes with examples of application to biological data obtained by confocal scanning light microscopy

Within the concept of point processes, a review is presented of quantities which can be used in studies of three-dimensional (3-D) aggregates of particles. Suitable characteristics and estimators are given for both unmarked and marked point processes. To demonstrate the feasibility of such quantitative approaches, an application in histology, dealing with 3-D arrangements of cell nuclei in rat liver, is described. Using a confocal scanning light microscope, 3-D images are recorded and image analysis used to obtain the coordinates of the centroid, together with the volume and DNA content, of each cell nucleus. Examples of results are given, using both unmarked and marked point processes. In the latter case, cell type, nuclear volume and ploidy group are suitable marks.     

激光平网雕刻机设计

研制了用于制作平面网版的激光雕刻机，设计了雕刻机用CO2激光器、光路系统及单片机控制系统，探讨了将图像文件转化为控制命令文件的方法。     

采用模数转换技术提高脉冲激光测距的测时精度

针对脉冲激光测距中计数量化误差影响测时精度的问题,本文提出了采用模数转换技术提高测时精度的方法,并进行了可行性与精度分析,理论与实践结果均表明,该方法易于实现,能够容易地将计数量化误差减少若干个数量级。     

激光熔敷合金层组织及腐蚀磨损特性研究

利用ＣＯ＿２连续激光器在４５钢表面进行了激光熔敷镍基合金、镍基Ｃｒ＿２Ｏ＿３合金和镍基ＷＣ合金，以２Ｃｒ１３不锈钢为对比材料，系统地研究了激光熔敷层在不同冲击速度和腐蚀介质浓度下的腐蚀磨损特性，并根据组织分析、显微硬度测试及腐蚀磨损后的表面形貌观察，探讨了激光熔敷层的腐蚀磨损过程。结果表明：激光熔敷层的腐蚀磨损性能均比２Ｃｒ１３不锈钢好。