纯铜双层辉光离子渗钛组织形成机理及性能分析

采用双层辉光离子渗金属技术对纯铜进行了渗钛处理。用配有能谱仪(EDS)的扫描电子显微镜(SEM)、X射线衍射仪和透射电子显微镜对合金层的显微组织形貌、钛含量分布、相组成及相结构类型进行了观察与测定，对合金层的形成机理进行了探讨，并对其性能进行了对比测定。结果表明：渗钛层由合金层和扩散层组成，合金层主要由TiCu (Cu)固溶体 TiCu4构成，TiCu4为Dla型有序相，TiCu为B2型有序相，扩散层为(Cu)固溶体。渗钛处理后纯铜的表面得到显著强化。     

有机电沉积涂料的新动向

阴极电沉积涂料是 2 0世纪 70年代以来发展起来的一种新的涂装方法 ,具有挥发性有机物 (VOCs)和有害空气污染物(HAPs)含量低、防蚀能力强、漆膜质量好、涂料利用率高、适合涂装结构复杂的构件和设备等特点。介绍了近年来阴极电沉积涂料研发的新动向。它们主要集中在有机双层电涂和高分子 聚电解质 /低聚物电解质复合物多层电涂体系 ,这些新的电涂体系在涂料的稳定性以及涂层的物理化学性质和力学性能方面具有明显的改进。     

New nanocomposite materials based on polymerization of [oligo(oxyethylene) methacrylates] in the presence of montmorillonite clay

Intercalation of poly[oligo(oxyethylene) methacrylates] onto sodium montmorillonite (MMT) clay has been investigated. A polymer–clay hybrid has been synthesized through intercalation of the monomer followed by its solution free‐radical polymerization. Eight polymer–clay hybrids were prepared using different weight ratios of clay, different oligo(oxyethylene) lengths and different proportions of crosslinker. Evidence of the development of nanostructures is obtained from scanning electron microscopy, and wide‐angle X‐ray diffraction studies support these results which show disappearance of the peak characteristic to d₀₀₁ spacing. In this hybrid MMT is dispersed homogeneously in the polymer matrix. © 2003 Society of Chemical Industry     

Low-resistance polysilicon process in contact application for high density devices

For the lowest resistance, it is required to have the epitaxial silicon contact between the silicon plug and the substrate and good step coverage at the high aspect-ratio contact holes, simultaneously. In this work, a double polysilicon (DPS) deposition technique was proposed for the requirements. The first, thin silicon layer is deposited in a single-wafer process chamber with an in-situ H₂-RTP (rapid thermal process) treatment for the epitaxial contact, and the second silicon layer is formed in a batch-type furnace for good step coverage. From chain resistance, Kelvin R_c, and current-voltage (I–V) measurement, the DPS process meets both low resistance and good uniformity, so that it suggests a breakthrough in the small-sized, semiconductor device application.     

NUMERICAL STUDY ON SORET-EFFECT AND DUFOUR-EFFECT FOR DOUBLE-DIFFUSIVE NATURAL CONVECTION IN POROUS ENCLOSURE

The influences of Soret effect and Dufour effect on the natural convection and heat and mass transfer for a porous enclosure were investigated by means of the penalty finite element method. Numerical results indicate that the Soret and Dufour effects have significant influences on heat and mass transfer in the presence of large temperature gradient and concentration gradient.     

C60高性能预拌混凝土的生产及应用

介绍了C60高性能预拌混凝土的研制及生产应用的过程与方法 ,对材料的性能、搅拌工艺进行了深入分析 ,为生产高强高性能混凝土提供了详细的思路     

GJ5×2双槽剥片机及其在高岭土剥片中的应用

GJ5×2大型双槽剥片机是国内超细物料加工中最新出现的超细磨/剥片设备,也是目前国内这一领域内最大规格的设备,已成功应用于煤系硬质高岭土剥片中,单机能力可达1.5～2.0t/h,产品细度可达小于2μm颗粒占85%～90%。     

Performance evaluation on a double‐layered satellite network

How to evaluate the performance of satellite networks is a prerequisite to the construction of satellite networks, and is also one of challenges in the researches on satellite networks. In this paper, generalized stochastic Petri net (GSPN) models are presented to carry out the performance analysis of a double‐layered satellite network. Firstly, the GSPN model of a double‐layered satellite network is simplified by proper analysis. Then, two sets of experiments are conducted to analyse the performance of the satellite networks, and show that the double‐layered satellite network outperforms single‐layered ones on the heavy traffic load. Finally, the feasibility and effectiveness of the proposed approach is verified by simulation experiments. Copyright © 2005 John Wiley & Sons, Ltd.     

钻井井架力学性能分析

钻井井架作为钻机系统设备中的关键部分,其力学性能直接关系到整套钻机系统的安全生产。文章推导了常用于分析钻井井架力学性能的理论,即线性屈曲、几何非线性和双重非线性理论。提出同时用这三种理论对钻井井架进行综合比较分析,从而合理地预见井架力学性能的方法。以A形钻井井架为例,进行了详细的分析,得到了井架的失稳形式、极限承载、破坏特征及薄弱部位,为钻井井架的设计、优化与评定提供了参考。     

双工频感应加热淬火技术在小型冷轧工作辊上的应用

双工频感应加热淬火Φ200mm以下的小型冷轧工作辊，其性能优于单工频感应加热淬火，延长了轧辊的使用寿命。