矿用大容量磷酸铁锂电池管理系统设计

为了保证矿用磷酸铁锂电池的安全性,结合煤矿工业实际需求,设计了8节单体60A·h磷酸铁锂电池串联、24V额定电压输出的矿用电池管理系统。该系统将微处理器配合集成芯片LTC6803组成电池保护模块,利用安时法估算电池组电量,采用电阻分流型均衡技术改善电池组性能。现场应用结果表明,该系统运行稳定可靠,保证了矿用磷酸铁锂电池的安全高效性。     

Highly ion-conductive solid polymer electrolytes based on polyethylene non-woven matrix

Highly ion-conductive solid polymer electrolyte (SPE) based on polyethylene (PE) non-woven matrix is prepared by filling poly(ethylene glycol) (PEG)-based crosslinked electrolyte inside the pores of the non-woven matrix. The PE non-woven matrix not only shows good mechanical strength for SPE to be a free-standing film, but also has very porous structure for high ion conductivity. The ion conductivity of SPE based on PE non-woven matrix can be enhanced by adding sufficient non-volatile plasticizer such as poly(ethylene glycol) dimethyl ether (PEGDME) into ion conduction phase without sacrificing mechanical strength. SPE with 20 wt.% crosslinking agent and 80 wt.% non-volatile plasticizer shows 3.1 × 10⁻⁴ S cm⁻¹ at room temperature (20 °C), to our knowledge, which is the highest level for SPEs. It is also electrochemically stable up to 5.2 V and has high transference number about 0.52 due to the introduction of anion receptor as an additive. The interfacial resistance between Li electrode and SPE is low enough to perform charge/discharge test of unit cell consisting of LiCoO₂/SPE/Li at room temperature. The discharge capacity of the unit cell shows 87% of theoretical value with 86% Coulombic efficiency.     

Cellulose as a binding material in graphitic anodes for Li ion batteries: a performance and degradation study

Four types of cellulose, in particular carboxy methyl cellulose (CMC), are tested as potential binding materials in graphitic anodes for lithium ion batteries. It is shown that a minimum content of a cellulose which gives acceptable anode properties (reversible capacity>300 mA h g⁻¹ during the first 10 cycles, irreversible loss<20%) is about 2 wt.%, which is less than in the case of conventional polymeric binders (5-10 wt.%). Kinetics of insertion-deinsertion and passivation processes seem not to be affected by the presence of cellulose. Explanation for the electrode failure at cellulose contents lower than 1 wt.% is given based on X-ray diffraction and microscopy investigations. Finally, the structure (distribution) of cellulose in the composite anode material is discussed and (indirectly) checked with a series of experiments. Most results are compared with the corresponding results obtained either with gelatin or conventional polymeric binders or both.     

高能量密度水溶性有机液流电池的开发策略

水溶性有机液流电池自2014年出现后发展迅猛,特别是近些年来有机电活性物质的降解和二聚导致的容量衰减问题得到初步解决后,该类液流电池有望作为大规模储能系统的候选者。然而能量密度较低的问题限制了其商业化的进程。对此,主要从增大溶解度、提高电化学窗口和电子的得失数这3个方面详细介绍了5种提高水溶性有机液流电池能量密度的方法——分子结构剪裁、“interaction-mediating”策略的应用、采用聚合物电活性物质、“氧化还原靶向”原理和电极表面的改性,同时对进一步提高水溶性有机液流电池能量密度的策略进行了简要展望。     

A Novel Inorganic Polymer as Cathode Material for Secondary Lithium Batteries

Summary: This paper introduces a new inorganic poly(phosphazene disulfide) material. With unique element composition and molecular structure, the polymer has noncombustible safety and preferable conductivity. When used as cathode material for rechargeable lithium batteries, the polymer's first discharge capacity is as high as 467.9 mAh · g^?1, which can be retained at 409.9 mAh · g^?1 after 60 repeated cycles. Therefore, it has a great application potential in the field of lithium batteries.

Replacement of the Cl atoms by S? S groups by refluxing Na₂S₂ and linear poly(dichloro‐phosphazene).     

电动汽车用锂离子电池热特性试验研究

为研究锂离子电池的热特性,以3 200 m A·h、3.67 V圆柱形三元材料锂电池为研究对象,进行了不同温度、不同充/放电倍率的热特性试验和低温加热试验.试验结果表明:随着充/放电电流的增大以及环境温度的降低,电池温度快速升高,低温下加热可以提高锂离子电池的充/放电性能.     

复合正极材料xLiFePO_4·yLi_3V_2(PO_4)_3/C的合成及其电化学性能

以聚吡咯(PVP K60)为表面活性剂和碳源,采用流变相法合成了x Li Fe PO4·y Li3V2(PO4)3/C正极材料样品。利用扫描电子显微镜(SEM)、X射线衍射仪(XRD)对样品形貌和结构进行了测试;采用电池测试仪和电化学工作站对样品电化学性能进行了测试,分析了不同复合比(x:y)对其结构和电化学性能的影响。研究表明:复合材料中存在两相复合与元素掺杂两种效应;当复合比为5∶1时材料的电化学性能最优,在0.1和10 C倍率下放电容量分别达到162.7和104.6 m Ah·g-1,且具有良好的循环稳定性。     

以Mn3O4为锰源合成高性能LiMn2O4正极材料

以Mn3O4为锰源,采用固相反应法,在较低的温度(650℃)制得尖晶石LiMn2O4正极材料。采用X射线衍射(XRD)、扫描电镜(SEM)、循环伏安和恒流充放电等技术对其相组成、微结构和电化学性能进行表征。结果表明该正极材料结晶良好,一次粒径约为150 nm。它的电化学性能,尤其是循环性能,明显优越于在较高温度合成的LiMn2O4。在电流密度为74 mA?g-1时,测得比容量为128 mAh?g-1,在1 480 mA?g-1时,比容量为105 mAh?g-1;在室温、148 mA?g-1充放电200次循环后,容量保持率为93%。     

Synthesis and characterization of triclinic structural LiVPO4F as possible 4.2 V cathode materials for lithium ion batteries

A potential 4.2 V cathode material LiVPO4F for lithium batteries was prepared by two-step reaction method based on a carbon-thermal reduction （CTR） process. Firstly, V2O5, NH4H2PO4 and acetylene black are reacted under an Ar atmosphere to yield VPO4. The transition-metal reduction is facilitated by the CTR based on C→CO transition. These CTR conditions favor stabilization of the vanadium as V^3＋ as well as leaving residual carbon, which is useful in the subsequent electrode processing. Secondly, VPO4 reacts with ElF to yield LiVPO4F product. The property of the LiVPO4F was investigated by X-ray diffractometry （XRD）, scanning electron microscopy （SEM） and electrochemical measurement. XRD studies show that LiVPO4F synthesized has triclinic structure（space group p I ）, isostructural with the naturally occurring mineral tavorite, EiFePO4-OH. SEM image exhibits that the particle size is about 2μm together with homogenous distribution. Electrochemical test shows that the initial discharge capacity of LiVPO4F powder is 119 mA·h/g at the rate of 0.2C with an average discharge voltage of 4.2V （vs Ei/Li^＋）, and the capacity retains 89 mA·h/g after 30 cycles.     

Si/CNTs@melamine-formaldehyde resin-based carbon composites and its improved energy storage performances

In this paper, Si/carbon nanotubes@melamine-formaldehyde resin (MFR)-based carbon (Si/CNTs@C) composites have been fabricated by surface modification, electrostatic self-assembly, cross-linking of MFR under hydrothermal treatment and further carbonization. The microstructure of the Si/CNTs@C composites was characterized, and the effects of CNTs content in Si/CNTs@C composites on their electrochemical performances were also investigated in detail. The results indicate Si/CNTs@C composites as anode materials of Li-ion batteries exhibit better high-rate and cycling performances compared to Si and Si@MFR-based carbon composites. Notably, Si/CNTs@C composites with 10.4 wt% CNTs show specific capacities of 1900, 1879, 1,688, 1,394, 1,189 mAh·g⁻¹ at 0.2, 0.5, 1, 2, and 3 A·g⁻¹, respectively. Even at 4 and 5 A·g⁻¹, their capacities still reach 970 and 752 mAh·g⁻¹, respectively. Moreover, they deliver a reversible capacity of 1,184 mAh·g⁻¹ at 0.5 A·g⁻¹ after 100 cycles. Therefore, the reasonable structure is of great significance for enhancing the electrochemical performances of Si-based composites.