采取具体措施 发挥教研室的职能作用

本文就如何发挥高校教研室的职能作用记述了本教研室所采取的具体方法和措施。     

Combined shape and sizing optimization of truss structures

 In this paper, an evolutionary optimization method is presented for weight minimum problem of a 3-dimensional truss structure in terms of nodal coordinates and element cross-sectional areas. The structure is subject to stress, local buckling and displacement constraints. Two types of design variables with different natures are optimized separately: (1) a fully stressed design (FSD) and scaling techniques are applied to sizing variables and (2) the evolutionary node shift method is applied to shape variables. Alternating procedure is utilized to couple the two types of variables and to combine the results. The optimum solution is achieved gradually from the initial configuration design. Two typical truss structures are examined to illustrate the validity of the method. Received: 22 October 2001 / Accepted: 04 June 2002 This research work is supported by the National Natural Science Foundation of China under the guarantees no. 10072050 and 10172072, respectively.     

The ponding problem on elastic membranes: an analog equation solution

 In this paper, the nonlinear response of elastic membranes with arbitrary shape under partial and full ponding loads has been analyzed. Large deflections are considered, which result from nonlinear kinematic relations. The problem is formulated in terms of the displacements components and the three coupled nonlinear governing equations are solved using the analog equation method (AEM). The membrane may be prestressed either by prescribed boundary displacements or tractions. Using the concept of the analog equation the three coupled nonlinear equations are replaced by three uncoupled Poisson's equations with fictitious sources under the same boundary conditions. Subsequently, the fictitious sources are established using a procedure based on the BEM and the displacement components as well as the stress resultants at any point of the membrane are evaluated from their integral representations. In addition to the geometrical nonlinearity, the ponding problem is itself nonlinear, because the ponding load depends on the deflection surface that it produces. Iterative schemes are developed which converge to the equilibrium state of the membrane under the ponding loads. Several membranes are analyzed which illustrate the method and demonstrate its efficiency and accuracy. The method has all the advantages of the pure BEM, since the discretization and integration is limited only to the boundary. Received 28 July 2001     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

微型灌注桩托换技术在地基基础加固工程中的应用

因场地淤泥等软土层深厚,在填方荷载作用下,软弱土层产生固结沉降,引起局部构筑物的不均匀沉降,发生结构破坏。采用微型灌注桩加固满足现场各个限制条件的要求,达到了加固目的。     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

多孔粒状铵油炸药在边坡预裂爆破中的应用

通过工程实践，介绍了利用多孔粒状铵油炸药进行边坡预裂爆破的设计原理及施工工艺。该技术能确保预裂爆破质量。简化施工工序，大幅度降低爆破成本。技术经济指标优越。     

The thermal ignition of lignocellulosics in infinite slab and cubic geometries

Wood shaving samples were heated in both cubic baskets and in a previously described system realising the conditions of the ‘infinite slab’ in thermal ignition. Results from the two sets of experiment were found to be totally consistent with each other.