结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

一种双光束自动测试光栅绝对与相对光谱衍射效率的原理性方案

提出了一种快速自动测试光栅光谱衍射效率的新方法。重点推导了测试平面光栅绝对光谱衍射效率与相对光谱衍射效率公式，介绍了双光束高精度自动测试光栅光谱衍射效率曲线的基本原理、方案与方法，并分析了测试精度。研究表明，本方案的测试速度和精度均比一般测试方法提高一倍，并能有效地消除光源波动对测量结果的影响，测量误差小于５×１０－３。     

GIC－4117／HC1．7MV Tandetron上的MeV离子注入系统

利用通用离子公司（ＧＩＣ）的４１１７型１．７ＭＶＴａｎｄｅｔｒｏｎ离子束分析设备进行ＭｅＶ级离子注入。所注入的离子能量范围由５００ｋｅＶ到１０ＭｅＶ，离子的质量在２４０ｕ以下，某些元素的负离子束流强度在１５０μＡ以上。双向机械扫描技术可将离子均匀地注入样片。     

Comparison of mass transfer efficiency in horizontal rotating packed beds and rotating biological contactors

In this study, the mass transfer efficiencies of a novel horizontal rotating packed (h‐RPB) bed and the conventional disc‐type rotating biological contactor (RBC) were studied at four speeds and seven submergences. Pall rings of two different sizes (25, 38 mm), superintalox saddles and a wiremesh spiral bundle were used as packings in the h‐RPB. Volumetric gas–liquid mass transfer coefficients were determined by unsteady state absorption of atmospheric oxygen in de‐aerated water. Power consumption per unit liquid volume has been found for all geometries tested. The oxygen transfer efficiency values for the h‐RPB were found to be 2–5 kg kWh^?1 and for the disc RBC were found to be 1–2 kg kWh^?1. The performance of the h‐RPB was also compared with other gas–liquid contactors such as surface aerators. The study proves that the h‐RPB is a energy efficient alternative to conventional contactors. Copyright © 2005 Society of Chemical Industry     

连续式超临界流体萃取进卸料装置

概括了超临界流体萃取技术和包括连续式操作在内的超临界流体萃取装置的研究现状 ,提出了一种通过球形进、卸料器完成固相物料超临界流体萃取连续化进卸料的装置 ,介绍了该装置的结构和工作原理 ,给出装置中各主要部件的计算方法。     

镁法海绵钛生产工艺中大型无隔板镁电解槽的节能实践

以镁法海绵钛生产工艺中大型无隔板镁电解槽的实际节能情况为例，探讨了在镁电解生产中的非生产耗电、生产耗电、漏电等因素造成的能量浪费，阐述了生产中粗镁直流电耗、电流效率、工作电压3者之间的关系，指出了影响电解槽工作电压的有关因素及降低电解槽工作电压的途径。     

混凝土浇筑质量对钢管混凝土性能的影响

着重阐述钢管与其核心砼粘结强度对钢管砼承载影响问题 ,并介绍三种常用浇筑方式和检测方法。     

LASER ENHANCED ELECTROCHEMICAL MACHINING PROCESS

An experimental apparatus was designed and built for the hybrid process of laser enhanced electrochemical machining (ECM). Comparison experiments had been done between solely ECM and laser enhanced ECM. The machining performance of hybrid process was investigated and compared with solely ECM. The principle of the hybrid process was exposed by analyzing the microstructure of machining surface. The results show that the hybrid process has advantages in machining accuracy, surface quality, and machining efficiency.     

Experimental Study of Concrete Subjected to Explosive Loading

The main subject of this paper is to demonstrate the response of structural concrete to different imposed strain rates. Attention is focused on the strain rate about 10^-2 s ^-1>, where some technical difficulties are experienced when an exact determination of mechanical properties for quasi-brittle materials is attempted. The design of a measurement system, which realizes computer acquisition, analysis, and graphic representation of data, is also presented.     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.