可与氟树脂基板相匹敌的热可塑性树脂基板材料

概述了可以与氟树脂基板相匹敌的低介质特性的热可塑性树脂基板材料的开发和应用。     

Sorption of Acid Green 25 on chitosan: Influence of experimental parameters on uptake kinetics and sorption isotherms

Acid Green 25, which is a diazoic dye bearing two sulfonic groups, is efficiently sorbed on chitosan. The protonation of chitosan may explain the electrostatic attraction of this anionic dye and that its optimum pH is close to 3. Preliminary protonation of amine groups (obtained by contact with a sulfuric acid solution) reduced the variation of solution pH following sorbent addition but significantly reduced sorption performance: the maximum sorption capacity of raw chitosan, 525 mg dye/g (0.84 mmol dye/g), was halved by acidic preconditioning. The acidic conditioning also reduced the kinetic rate—the time necessary to reach equilibrium increased up to threefold depending on the experimental conditions. The size of sorbent particles influenced sorption kinetics and equilibrium because of resistance to intraparticle diffusion, but the sorption appeared to occur not only at the surface of the sorbent but also in the intraparticle network of the polymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1073–1080, 2003     

超深亚微米非对称Halo LDD低功耗新器件的研究分析

提出了一种新的器件结构——非对称Halo L DD低功耗器件,该器件可以很好地抑制短沟效应,尤其可以很好地改善DIBL效应、热载流子效应以及降低功耗等,是低功耗高集成度电路的优选结构之一.分析了非对称HaloL DD器件的主要特性,并将其与常规结构、非对称L DD结构、非对称Halo结构的器件进行了比较并进行了参数优化分析.     

低熔融指数聚丙烯的开发生产

总结了开发生产低熔融指数聚丙烯的试验过程与结果，通过优选催化剂、优化操作过程、控制加氢量，生产出质量稳定可靠的熔融指数在0．2～0．5g/l0min之间的低熔融指数聚丙烯．     

脆断事故的原因分析和预防措施

分析高强度材料和大型工程结构元件发生低应力脆性断裂的原因及条件，指出传统强度设计理论的局限性，从设计和工艺上提出防止发生低应力脆断事故的具体措施，给使用高强度材料和设计大型工程结构元件时提供参考。     

HPD-2型非临氢降凝催化剂工艺实验

利用HPD-2型非临氢降凝催化剂进行了中试实验。结果表明：HPD-2型非临氢降凝催化剂相对其他的同类催化剂产品液体收率较高，最高可达95％以上；在反应温度为380℃时，凝点降幅在50℃左右，降凝效果较好；产品性质稳定，具有很好的应用前景。     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.     

液氨储罐保冷改造效果评定

作者结合实例，论述了氨罐保冷改造的设计、选材及施工，给出了改造后两年的测试结果，并对测试结果进行了分析。     

柴油机针阀体的乙炔低压渗碳

乙炔低压渗碳可以有效地避免在真空渗碳过程中产生炭黑和焦油，同时由于乙炔具有较高的供碳能力，使这一技术尤其适用于针阀体这样的小直径深盲孔零件。