GPS在水面流速流向测量中的应用

传统的水面流速流向测量多采用经纬仪交会法,此法需要大量的人力和设备,工作量大且费时。近几年,随着全球定位系统(GPS)的广泛应用和实践,在一定范围内,采用GPS定位法替代经纬仪交会法施测水面流速流向。介绍了GPS定位法的测量原理、设备,以及测量方法。通过对GPS定位法的精度和优缺点的分析,得出采用GPS定位法施测水面流速流向具有较高的推广价值。     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

凤滩水电厂自动发电控制策略

介绍了凤滩水电厂自动发电控制(AGC)策略的实现方法,重点介绍了修正等容量比例有功分配方法及相应措施.程序设计的原则是,机组紧跟目标负荷的情况下,在最佳效率下运行,同时减少机组开/停机次数、有功调节频率和跨越振动区次数,从而减少机组磨损,兼顾运行效率和机组运行安全.     

Lactic acid production from dining‐hall food waste by Lactobacillus plantarum using response surface methodology

BACKGROUND: Food waste generally has a high starch content and is rich in nutritional compounds, including lipids and proteins. It therefore represents a potential renewable resource. In this study, dining‐hall food waste was used as a substrate for lactic acid production, and response surface methodology was employed to optimise the fermentation conditions. RESULTS: Lactic acid biosynthesis was significantly affected by the interaction of protease and temperature. Protease, temperature and CaCO₃ had significant linear effects on lactic acid production, while α‐amylase and yeast extract had insignificant effects. The optimal conditions were found to be an α‐amylase activity of 13.86 U g^?1 dried food waste, a protease activity of 2.12 U g^?1 dried food waste, a temperature of 29.31 °C and a CaCO₃ concentration of 62.67 g L^?1, which resulted in a maximum lactic acid concentration of 98.51 g L^?1 (88.75% yield). An increase in inoculum size would be appropriate for accelerating the depletion of initial soluble carbohydrate to enhance the efficiency of α‐amylase in dining‐hall food waste fermentation. CONCLUSION: A suitable regression model for lactic acid production was developed based on the experimental results. Dining‐hall food waste was found to be a good substrate for lactic acid fermentation with high product yield and without nutrient supplementation. Copyright © 2008 Society of Chemical Industry     

A novel direct aerodynamically assisted threading methodology for generating biologically viable microthreads encapsulating living primary cells

In a recent discovery, coaxial electrospinning was explored to encapsulate living organisms within a continuous bio‐polymeric microthread from which active biological scaffolds were fabricated (Townsend‐Nicholson and Jayasinghe, Biomacromolecules 2006, 7, 3364). The cells were demonstrated to have gone through all expected cellular activity without their viability being compromised. These biologically active threads and scaffolds have direct and tremendous applicability from regenerative to therapeutic medicine. Currently these post‐processed cells as composite threads and scaffolds are being investigated in‐depth at a cellular level to establish if the processing methodology has any affect on the cellular make‐up. We now demonstrate a competing non‐electric field driven approach for fabricating composite threads and scaffolds influenced only by a differential pressure. We refer to this novel composite thread to scaffold fabrication methodology as coaxial aerodynamically assisted bio‐threading (CAABT). Our investigations firstly, demonstrate that this technique can process handle living organisms without biologically perturbing them in anyway. Secondly the process is elucidated as possessing the ability to form composite active threads from which biologically viable scaffolds are formed. Finally our study employs florescent activated cell sorting (FACScan), a method by which the cellular dynamics and viability are quantified on control and threaded cellular samples at two prescribed time points. In parallel with FACScan, optical comparison of cellular morphology at three time points within a period of three weeks is carried out to photographically observe any changes in the post‐processed cellular phenotype. Our developmental investigations into this novel aerodynamically assisted threading methodology has unearthed a unique biomicrofabrication approach, which joins cell electrospinning in the cell threading to scaffold fabrication endeavor. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of polyurethane resins and its improvement on dimensional stability and finishing performances of medium‐ and small‐diameter softwoods

This study analyzed the effects of polyurethane (PU) resin treatments on surface homogeneity, dimensional stability, and finishing performances of medium‐ and small‐diameter softwoods produced in Taiwan. Two‐pack PU resins were prepared by combing short castor oil‐modified alkyd resin serving as a polyol with polymeric 4,4′‐diphenymethane diisocyanate (PMDI) serving as a hardener, by the molar ratio of NCO/OH+COOH of 1.2. Four types of short oil‐modified alkyd resins with different polyhydric alcohols (glycerin and pentaerythritol) and polybasic acids (phthalic anhydride and isophthalic acid) were synthesized. Three kinds of medium‐ and small‐diameter softwoods, including China fir, Taiwanina, and Japanese fir with a diameter of 10–15 cm were obtained from Hui‐Sun Forest Station, Taiwan. The wood coating of nitrocellulose (NC) lacquer including sanding sealer and top clear was used. Results show that the surface hardness, homogeneity, moisture excluding efficiency, and antiswelling efficiency of woods were enhanced by PU resin treatments. Among all the PU resins, the isophthalic acid and pentaerythritol‐containing PU resin (IPA‐P‐MDI) achieved the best improved efficiency on dimensional stability of woods. Results of two types of finishing procedure, i.e. NC lacquer sanding sealer plus top clear and top clear only, applied onto the PU‐treated woods revealed that the hardness, adhesion, and durability of NC lacquer films on the PU‐treated wood were superior to those of untreated one, especially for top clear finishing alone. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The synthesis of block copolyetherketones based on 4,4′‐dichlorodiphenylketone,phenolphthaleine, and bisphenol A and investigation of their properties

Block structured polyethers based on phenolphthaleine, 4,4′‐dichlorodiphenylketone, and bisphenol A with different degrees condensation (n = 1, 5, 10, and 20) were synthesized by means of acceptor‐catalytic polycondensation. Equaimolar quantities of chloranhydrides of iso‐ and terephthalic acids were used. Higher molecular masses were obtained from longer oligoketones with higher condensation degrees. Better molecular packing, increased thermal and mechanical properties were obtained with higher condensation degrees of oligoketones. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008     

A strategy for the electro-organic synthesis of new hydrocaffeic acid derivatives

Electrochemical treatment processes can significantly contribute to the protection of the environment through the minimization of waste and toxic materials in effluents. From a pharmaceutical point of view and due to the existing resemblance between the electrochemical and biological reactions, it can be assumed that the oxidation mechanisms on the electrode and in the body share similar principles. In this paper, the application of electrochemical studies in the design of an environmentally friendly method was delineated for the new hydrocaffeic acid (HCA, 3,4-dihydroxy hydrocinnamic acid) derivatives synthesis at carbon electrodes in an undivided cell. In this cell, the EC mechanism reaction was involved, comprising two steps alternatively; (1) electrochemical oxidation and (2) chemical reaction. In particular, the electro-organic reactions of HCA, an important biological molecule, were studied in a water–acetonitrile (90:10 v/v) mixture in the presence of benzenesulfinic acid (3) and p-toluenesulfinic acid (4). The research included the use of a variety of experimental techniques, such as cyclic voltammetry, controlled-potential electrolysis and product spectroscopic identification.     

Exergy losses in refrigerating systems. A study for performance comparisons in compressor and condenser

A study is carried out to describe irreversibilities in one stage refrigerating process for vapour compression cycle with refrigerant mixtures R-404A, R-410A, R-410B and R-507 as working fluids. They are calculated as exergy losses by an algorithm developed on the basis of thermodynamics. The proposed relationships have been derived from exergy balances on the system components. Emphasis is placed on parameters influencing the losses and the related results are presented through Grassmann diagrams (diagrams of exergy fluxes). Furthermore, detailed information on the variation of cycle's exergy efficiency with evaporating and condensing temperatures is given. Copyright © 2003 John Wiley & Sons, Ltd.     

Memory of Distributed Computer Systems: Distinctive Features of Their Architectural-Structural Organization and Use

Distinctive features of architectural-structural organization and use of memory networks are considered with the aim of choosing an optimal configuration in designing distributed computer systems.